Computer display screen assembly seems simple, but it makes many novice users have difficulties. Today, PHP editor Zimo will bring you guidance on the display assembly process, allowing you to easily assemble your display and say goodbye to the troubles of tedious steps.
1. The base of monitors purchased online is generally separated from the monitor. After docking the base and the monitor, screw the bolts to the connection between the base and the monitor according to the hole positions.
2. Then find the connection port and power cord location of the monitor, then tighten the connection between the monitor bracket and the monitor to complete the fixing of the monitor bracket.
3. Find the interface cable of the monitor, take out the protective cover, and connect the monitor interface and the interface cable.
4. Find the interface cable of the monitor, take out the protective cover, and connect the monitor interface and the interface cable.
5. After connecting, connect the monitor power cord to the power source, then connect the cable to the same port on the computer, turn on the computer, and see the screen loading to confirm that the display connection is completed effectively.
It’s not too tiring to assemble a computer display screen. Because assembling a computer display is not a physical job, but a skill job. Sit down on the chair and place the parts on the table. You can install these computer monitors and accessories.
It is not recommended to buy an assembled computer screen monitor. After all, you can buy a good brand computer monitor for a few hundred yuan, and the assembled one is much cheaper.
1. If the monitor is powered on but shows no signal, shut it down (if a short press of the power switch does not work, press and hold the switch until the power indicator light goes out or unplug the power cord directly). Turn off the power, open the case, and re-insert and unplug the memory. strips, and wipe the gold finger with an eraser in one direction (scraping the back of your thumb nail will also work), and then turn on the phone after installation. If you don't know how to operate it, then it's simple: just kick the chassis (note the location: the center of the side of the left and right side of the chassis that has no interface at the back). If it's a laptop, you can't kick it, but other operations are the same.
2. If the above operation is ineffective, shut down the computer, open the case, re-insert and unplug the graphics card, and tighten the data cable between the monitor and the graphics card. If it still doesn't work, consider the graphics card is damaged and replace it with a new one.
3. If the monitor does not have power (the indicator light does not light up), look at the back of the monitor, plug the power cord plug connected to the monitor upwards, and check whether there is power from the other end of the power cord to the socket.
4. If the host can be displayed when connected to other monitors or the local monitor still cannot be displayed when connected to other normal hosts, it means that the monitor is damaged and needs repair
1. Possible 2. Due to fierce market competition, continuous technological advancement and cost reduction, it is possible to assemble a computer with a display price of 3,500 yuan in 2021. With the development of technology, the prices of electronic products have gradually dropped. At the same time, when assembling computers, you can selectively purchase cost-effective parts to achieve a lower total cost. 3. With the development of the electronic product market, computers and display screens of various brands and models continue to emerge, and the prices also vary. If you pay attention to cost-effectiveness when buying a computer, choose the right parts and brands, and assemble it by yourself, it is very likely that you can buy a better-performing computer with a display in 2021 with a budget of about 3,500 yuan.
1. First, assemble the cut profiles, that is, assemble the outer frame of the display screen. Common profiles on the market are mainly square and round, but the assembly methods are the same.
2. After assembling the outer frame, place the unit board inside the frame (pay attention to the front and back sides of the frame, the grooved side is the front side). At this time, the position of installing the back strip is quite accurate to avoid If one mistake is made, the whole thing will be changed.
3. After the back strip is fixed, be sure to check whether there are iron filings on the circuit board on the unit board after the back strip is fixed. If so, clean it. Otherwise, it will cause a short circuit on the unit board, dead lights or frequent failures. On, remove the frame and install the magnet.
4, fix the unit board
5, connect the cable, upper and lower power cables
6, fix the power supply and control card
Answer:
The assembly of the digital display screen needs to follow the following steps:
1. Prepare all components of the digital display screen, including the motherboard and LED lamp beads , power supply, controller, etc.
2. Arrange the LED lamp beads on the motherboard according to certain rules, and connect the power supply and controller.
3. Fix the motherboard on the casing of the digital display and connect the lines between the various components.
4. Carry out power test and controller test to ensure that the digital display screen can work normally.
5. Finally, install and fix the shell, and the assembly of the digital display is completed.
Reason and content extension:
The digital display screen is a display device widely used in commercial advertising, public information release and other fields. Its assembly needs to be carried out according to certain rules and steps. to ensure its normal working and stability.
During the assembly process, attention needs to be paid to the correctness of the connections and wiring between the various components. The power supply and controller also need to be tested to ensure that the digital display screen can work properly.
It won’t be difficult. You only need to do one thing repeatedly in assembly line work. This kind of work is quite tiring and hard on the eyes. Come on
There are drawings when you buy a computer desk, just assemble it according to the drawings
1. First connect the VGA cable to the monitor, and then fix the two screws at the back. The main reason for fixing is to worry about the connecting wire falling off when moving.
2. Then connect the other end of the VGA cable to the computer host.
3. Next, connect the power cord to the monitor. (Note that you are only connecting to the monitor. Do not connect the other end of the power cord to the socket. Wait until all connections are completed before turning on the power.)
4. Next, connect the mouse to the host.
5. Connect the keyboard as well. (The green one is the mouse, and the purple one is the keyboard. Also note that the internal pins of the mouse and keyboard plugs must be aligned with the pinholes in the interface before they can be inserted.) Connect one end of the network cable to the RJ45 interface of the computer host, and then connect the other end to the switch or router or modem.
6. Next, connect the power cord of the host.
7. Next, you can connect the power plugs of the host and monitor to the sockets to power on the host and monitor. You can start and use it normally.
The above is the detailed content of How to assemble a computer monitor? Are you tired of assembling a computer monitor?. For more information, please follow other related articles on the PHP Chinese website!
![[Web front-end] Node.js quick start](https://img.php.cn/upload/course/000/000/067/662b5d34ba7c0227.png)
