I just unplugged the usb1 and usb2 cable sockets on the computer motherboard and forgot how to plug them back in?

I don’t know how to plug it back in after unplugging the USB port on the motherboard? don’t worry! PHP editor Strawberry brings you a detailed guide on plugging and unplugging USB sockets. This article will guide you on how to easily identify different USB cables and accurately plug them back into your motherboard to ensure your device is working properly. Read on to learn more.

I just unplugged the usb1 and usb2 cable sockets on the computer motherboard and forgot how to plug them back in?

USB1 and USB2 can swap positions.

The reasons are as follows: 1. USB1, 2, 3, and 4 on the computer motherboard represent the USB numbers. 2. These numbers are to distinguish the serial numbers of the USB front sockets on the computer motherboard. When actually using the computer, selecting USB1 or USB2 for the front USB interface has no impact or difference on the function of the USB.

How to disassemble the large plug of the computer board?

Pinch the latch on the side of the plug with your hands to disengage the latch, then use a little force to pull it up and pull it out. The interface that supplies power to the motherboard adopts a fool-proof design and can only be inserted in the correct way. Through observation, it can be found that there is a raised groove on one side of the motherboard's power supply interface, and a snap-on design is also used on one side of the power supply interface.

Requesting support, how to open the SATA interface that is closed in DOS on the motherboard?

It should be the motherboard BIOS. If you operate it normally, it may be difficult to describe. Here are two quick methods:

1. After starting the computer using the soft method, immediately press the "Del" key. Enter the BIOS interface, select "locad bios defaults (load default BIOS settings)", save and press "F10" to exit to open SATA.

2. If the hard method is still troublesome, unplug the power cord of the host, remove the motherboard battery, let it sit for a few minutes (3~5 minutes), then put it back on, power on and start, it may be possible You need to press "F1" to load the default parameters and open SATA.

I can’t even pull out the SATA cable from the motherboard. Need help?

The cable that connects the hard drive to the motherboard usually has a card. You can gently press the card with your hand and then gently pull it out.

The connection cable between the hard disk and the motherboard is generally a data cable with a SATA interface. This kind of wire is usually a four-core parallel wire. In order to prevent the connection from being unstable, it usually has a clip on it. When you insert it, you will hear a click and the upper clip will lock.

If you don’t press the clip, you can’t pull it out directly.

How to unplug the host power cord connection port?

You need to pinch the hook on the power plug with your hands, and then you can pull it out. The computer power cord refers to the input of 220v AC power to the computer host atx power supply. The computer power cord is an essential part of the computer. Its function is to connect the motherboard power supply and CPU power supply.

Reset switch: Two-pin. The plug connected to this switch is usually marked with reset sw, and the English abbreviations near the corresponding pins on the motherboard are generally reset, rst, rs or re, etc. Regardless of positive or negative, it is still effective if plugged in reverse.

Power light: The connection is also a two-pin plug. One connection is generally indicated by green, and the other connection is white.

How to unplug the cable?

The cable connection part is divided into three parts. One is the cable holder, which is welded to the motherboard. The other is the cable. No need to explain. The most important one is the cable fixing clip.

If you observe carefully, you will find that there is a slender strip at the interface of the cable holder. Press it on the interface of the cable. Use a small screwdriver or your hands to gently push both ends in the direction of the cable. The clip is pushed out 2-3mm, and the cable can be gently pulled out.

How to remove the m.2 screw posts of the motherboard?

Check the position of the screw, use a screwdriver and hammer to gently tap out the screw. When replacing screws, you can put a layer of tissue paper on the new screws so that the screw threads can be tightened.

Or you can find a hacksaw blade and re-saw a groove on the screw, and then use a flat-blade screwdriver to remove it. Be sure to cut deeply enough and insert the screwdriver firmly.

How to remove the graphics card from your computer?

Steps to unplug the graphics card:

1. Unplug the power supply.

2. Lay the chassis down with the motherboard facing up.

3. Use a screwdriver to remove the screw (the blue jack connected to the monitor is connected to the graphics card) and the chassis.

4. The graphics card slots are different. In some cases, you can pull the tail to the right and pull it out with the other hand. Some can be pulled out directly, while others can be pushed down and then pulled out.

5. I'm researching it myself. Don't use too much force and pull it straight. Be careful not to prick your hand with the thorny Core fan.

The graphics card is connected to the computer motherboard. It converts the digital signal of the computer into an analog signal for display on the monitor. At the same time, the graphics card still has image processing capabilities, which can assist the CPU in working and improve the overall running speed. For professionals For graphic designers, graphics cards are very important.

How to check the interfaces on the motherboard?

Generally, you can search for hard drives that support interfaces by checking the motherboard model.

You can also take a look at it yourself. If there is a small SATA port on it, it supports it. If it is a wide IDE port, it supports IDE port. If your IDE port hard drive is broken, it is recommended that you buy a capacity one. A hard drive with a SATA interface that is too big (maybe it does not support large capacity, 500G should generally be enough), then go to the small counter selling spare parts in the computer city to buy an adapter card that costs about ten yuan, and convert it to SATA Just the interface.

The above is the detailed content of I just unplugged the usb1 and usb2 cable sockets on the computer motherboard and forgot how to plug them back in?. For more information, please follow other related articles on the PHP Chinese website!