What to do if the computer has a blue screen after turning on the computer

How to deal with a blue screen after the computer starts up

1. The solutions to the blue screen after the computer starts up include: overclocking appropriately, cleaning or replacing the memory module, detecting bad sectors on the hard disk, Uninstall software installed later and scan with anti-virus software. Appropriate Overclocking From a hardware perspective, excessive overclocking is a major cause of blue screens.

2. Since most blue screen failures caused by memory are caused by excessive internal dust or poor contact, the solution is also very simple. You only need to open the computer case, pull out the memory stick, and clean it. General problems can be solved by removing the slot and cleaning the gold finger of the memory module before putting it back.

3. After power outage, forced shutdown, or sudden crash, the computer will self-check and count down the seconds after booting, and display a blue screen. Since it is a hard disk check disk process, the computer can finish reading naturally and cannot be stopped with the abort key; there is poor contact between the memory and the memory slot, the graphics card and the graphics card slot, and a blue screen is displayed with an error code.

4. You can cut off the power first, open the computer case, take out the memory stick, and use an eraser to rub the golden finger area (that is, the place with the copper piece) back and forth a few times. Then change another memory slot and plug it back in, and that's it. Press F8 while booting up, enter Advanced, select Last Known Good Configuration, and OK.

What to do if the computer keeps blue screen after startup

Solution one: You can cut off the power first, open the computer case, pull out the memory stick, and use an eraser to point to the golden finger part (that is, Where there are copper pieces, wipe it back and forth a few times, then replace it with a memory slot and plug it back in. That's it.

The solution to the third possible cause is to replace the hard drive, because the blue screen may be due to a problem with the hard drive.

Turn on the computer and press F8 until the advanced options appear. Release it, select "Last Known Good Configuration" and press Enter to repair. Press F8 on boot to enter safe mode and then exit. Select restart or shutdown before booting to enter normal mode (repair the registry).

How to deal with frequent blue screen problems on computers: Click to open 360 Security Guard, open its interface and find "Manual Service" at the bottom, enter "blue screen" in the input box and search. After searching for the solution, you can see the relevant solution below the input box, and click "Repair Now" behind it.

The solution is to turn on the computer and press the DEL key (or the key prompted on the boot screen) to enter the motherboard BIOS and initialize the BIOS setting information. Usually press F9 to restore the factory default settings, then press F10 to save and exit and restart the computer. 3. CMOS (BIOS) setting error, mainly due to problems with software setting options.

What to do if the computer has a blue screen as soon as it is turned on

1. Restart the computer: Restart the computer normally in the current state, or press the host restart button to restart the computer, or press and hold the power button to force shutdown and then restart. , if the error message no longer appears and the system operation can be entered normally, it means that the last abnormality was just an occasional program or system operation error and does not matter.

2. Check the hardware: Sometimes the blue screen is caused by hardware failure, such as memory, hard disk, etc. You can try to re-plug the memory module or replace the hard disk. If it is a desktop computer, you can also check whether the power supply is normal. Shut down and restart: Try shutting down and restarting. If the blue screen only occurs occasionally, it may be resolved automatically.

3. You can use the DG partition tool to detect and repair bad sectors. Method 4: The installed software is incompatible and causes a computer blue screen. Most problems such as software incompatibility occur, but this kind of computer software incompatibility generally rarely occurs.

How to solve the blue screen after the computer is turned on

Solution: If you find that the computer has a blue screen, you can perform anti-virus operations after restarting the computer next time. It is recommended to use the current mainstream anti-virus software to check for virus Trojans .

The solution to the second reason is to try to start Windows in safe mode. Press the F8 key when booting and select "Safe Mode".

You can cut off the power first, open the computer case, take out the memory stick, use an eraser to rub the gold finger part (that is, the place with the copper piece) back and forth a few times, and then replace it. Just plug one memory slot back in and that's it. Press F8 while booting up, enter Advanced, select Last Known Good Configuration, and confirm.

The solution is to turn on the computer and press the DEL key (or the key prompted on the boot screen) to enter the motherboard BIOS and initialize the BIOS setting information. Usually press F9 to restore the factory default settings, then press F10 to save and exit and restart the computer. 3. CMOS (BIOS) setting error, mainly due to problems with software setting options.

The above is the detailed content of What to do if the computer has a blue screen after turning on the computer. For more information, please follow other related articles on the PHP Chinese website!