Why is there no signal on the monitor after turning on the computer?
Reasons for no signal on the monitor after the computer is turned on: 1. The host connection of the monitor data cable is loose or has poor contact; 2. The memory module is loose or there is too much dust; 3. The display is faulty, it is recommended to find a professional Maintenance personnel should perform maintenance; 4. If the motherboard is faulty, it is recommended to contact professional maintenance personnel for maintenance.
The operating environment of this tutorial: windows10 system, DELL G3 computer
I don’t know if you have encountered such a situation, that is, the computer uses time After a long time, I found that there is no signal on the monitor after turning on the computer. How do you usually solve this situation? Today the editor has brought you relevant tutorials, I hope it will be helpful to you.
The monitor shows no signal when the computer is turned on. I believe many friends have encountered this situation. Do you know what the reason is and how to solve it? Let’s analyze it together.
#1. When the host connection of the monitor data cable is loose or has poor contact, the computer monitor will display no signal. This problem is easier to solve. Check whether the computer data cable has fallen off. If so, reconnecting it will solve the problem. If there is poor contact or the data cable is damaged, you can directly replace it with a new data cable.
2. This situation can also occur if the memory module is loose or there is too much dust. The most obvious situation is that the host is running normally, but there is no signal on the monitor. We can take out the memory stick, clean the dust on it with a paper towel, and then put the memory stick back in its original position. The problem of no signal on the display screen will be solved.
3. The display screen is faulty. This can also happen if the monitor itself is broken. Generally, if there is no signal on the monitor, it is most likely due to an abnormality in the high-voltage board, a fault in the backlight circuit, or a fault in the AD driver board. These faults generally cannot be solved by oneself. It is recommended to find professional maintenance personnel for maintenance. If the fault is too large and repair is cost-effective, you can also buy a new monitor directly.
4. Motherboard failure will also cause you to be unable to boot and display no signal. This cannot be solved directly. It is recommended to contact professional maintenance personnel for maintenance.
The above is the detailed content of Why is there no signal on the monitor after turning on the computer?. For more information, please follow other related articles on the PHP Chinese website!
Hot AI Tools
Undresser.AI Undress
AI-powered app for creating realistic nude photos
AI Clothes Remover
Online AI tool for removing clothes from photos.
Undress AI Tool
Undress images for free
Clothoff.io
AI clothes remover
AI Hentai Generator
Generate AI Hentai for free.
Hot Article
Hot Tools
Notepad++7.3.1
Easy-to-use and free code editor
SublimeText3 Chinese version
Chinese version, very easy to use
Zend Studio 13.0.1
Powerful PHP integrated development environment
Dreamweaver CS6
Visual web development tools
SublimeText3 Mac version
God-level code editing software (SublimeText3)
Hot Topics
1377
52
How to modify the startup item configuration of Win11? Win11 startup item configuration modification guide
Jan 29, 2024 pm 04:00 PM
When we use computers, there are some applications that we often use, which makes many users set these commonly used applications as startup items. So how to adjust the win11 startup items? Users can directly open the run window and enter the system settings interface to perform operations. Let this site carefully introduce to users how to adjust the win11 startup items. How to adjust the win11 startup items 1. You can first press Win+R on the win11 system to open the run window and enter msconfig to open the system startup items. 3. Find the startup tab and open it. There is a faster way, press WIN+X keys to bring up the shortcut menu, find the task manager and open it, you can start it directly
How to manage startup items in Windows 10
Feb 07, 2021 am 11:22 AM
Method: 1. Press "win+R" to open the "Run" window, enter the "msconfig" command, and click "Confirm"; 2. In the msconfig setting interface, click the "Startup" tab and click "Open Task Manager"; 3. In the Task Manager interface, click the "Startup" tab; 4. Find and select the unwanted startup item, right-click the mouse, and select "Disable" in the pop-up menu.
Teach you how to set win10 startup items
Dec 27, 2023 pm 10:06 PM
Recently, many users have asked me how to set the startup items at startup. In fact, it is very simple to set up. Just set it to automatic startup and it will run automatically at startup. Let’s take a look at the detailed tutorial below. Win10 startup item setting tutorial Click the shortcut key "win+r" to open the run window dialog box. Enter "msconfig" in the box and click, and the system configuration dialog box will pop up. Click Startup Options at the top of the System Configuration dialog box to open the Task Manager option in the frame. All startup items will be displayed, and the status bar of each item will show whether it is enabled. Boot Figure-5 For example, if the Baidu Netdisk in the picture is prohibited from starting up, then you only need to right-click the Baidu Netdisk option, and the option bar that pops up will have Enable and
How to set startup items at startup How to set up computer startup items
Jan 12, 2024 pm 02:06 PM
I believe everyone knows that some programs will automatically start when you turn on the computer. If there are too many programs started, the boot speed will be very slow. Many users don’t know how to cancel the startup items. Many of the startup items are programs that do not need to start automatically. How to set the startup items? Below, the editor will share with you my experience in setting startup items. Most software hopes to be able to start on its own, so when we install the software, the general security software will prompt that the software being installed is modifying the startup items. Do you want to pass these? If you feel that your computer starts up very slowly. , then you can consider setting the computer's startup items. Below, the editor will introduce to you the steps to set the startup items. How to set the startup item and click the shortcut key "
How to set startup items in Win11 system
Feb 07, 2024 pm 04:15 PM
How to set startup items in Win11 system (tutorial on how to set startup items) In the process of using the computer, we often encounter some software or applications that need to be automatically started when the computer is turned on. This saves us the trouble of opening them manually and improves work efficiency. This article will introduce how to set startup items in Win11 system to help you easily achieve self-starting. Method 1: Use Task Manager to set startup items 1. First, press the Win+X key combination and select "Task Manager" to open the Task Manager. 2. In the Task Manager window, click the "Startup" tab. 3. In the Startup tab, you can see a list of applications that have been set to start at startup. If you want to add a new startup item, click
Teach you how to set startup items in win7
Jul 10, 2023 am 09:29 AM
Some software installed on the computer may set the function of auto-starting at startup. Sometimes too many startup items will cause the computer to start slowly. Therefore, some netizens want to set the startup items of win7 to disable or enable some startup items. So how to set the startup items in win7? The editor below will teach you how to set the startup items in win7. The specific steps are as follows: 1. Open the "Start" menu, enter "msconfig" in the search box and press the Enter key. 2. In the pop-up "System General", check "Selective Startup". 3. Click "Start" above to see the auto-start items. 4. Check or cancel the application according to your needs, and restart it to take effect. 5. In addition, there is another
How to set startup items for win10 home version
Jan 13, 2024 pm 01:45 PM
Sometimes for the sake of convenience, we will set up some software to automatically start when the computer starts up. However, some users are not very familiar with these settings. They set up the startup but find that it does not take effect. Then there may be problems with Win10 Home Edition from the following aspects. Why can't the startup items be set? 1. Press win+R, open and run and enter "gpedit.msc" 2. Expand Computer Configuration - Windows Settings - Security Settings - Local Policy - Security Options 3. Find User Account Control: as administrator Approval mode runs for all administrators, set to disabled
Why is there no signal on the monitor after turning on the computer?
Jun 30, 2023 am 11:17 AM
Reasons why there is no signal on the monitor after the computer is turned on: 1. The host connection of the monitor data cable is loose or has poor contact; 2. The memory module is loose or there is too much dust; 3. The display screen is faulty. It is recommended to find a professional maintenance personnel for repair; 4. If the motherboard is faulty, it is recommended to contact professional maintenance personnel for repair.