How to restore MSI motherboard BIOS to default settings?

How to restore MSI motherboard BIOS to factory settings?

The method for restoring MSI motherboard BIOS to factory settings is as follows

Method 1

1. Remove the button battery on the motherboard, keep it above 15 cents after removal, and then install it. This can erase BIOS information and restore factory settings.

2. Of course, some motherboards are also equipped with "hard jumpers". Just follow the prompts and use a jumper cap to short pins "2" and "3" to clear the BIOS information.

Method 2,

1. When turning on the computer, after some information prompts such as "Press DEl to enter BIOS" and "Press F1 to run the installation program" appear at the bottom of the screen, press the DELETE key to enter the Bios program interface. .

2. After entering the BIOS interface, move the cursor to the "Load Optimized Default" item and press Enter;

3. Then select "Yes" in the pop-up window and press the Enter key reset. Finally, press F10 to save it.

How to clear bios on MSI motherboard?

Answer: The steps for clearing the BIOS on an MSI motherboard are as follows: 1. Short-circuit the pins. There is a JBAT1 pin on the MSI motherboard, which can be used to discharge the battery instead. The operation is also relatively simple. After cutting off the external power supply, you can touch the two pins at the same time with a metal object. The metal object can be a ballpoint pen tip, a 1 yuan coin, a metal-head screwdriver, etc. It usually takes about 3 seconds to clear the pins. BIOS.

The JBAT1 pin is usually located near the CR2032 battery. Some newer motherboards have been moved to the lower right corner of the motherboard, which is easier to access than near the battery. Another little tip is that players who like to mess around can connect the RW restart switch of the chassis to JBAT1, so that it can be cleared quickly.

2. Physical button There is a button to clear CMOS on the back I/O shield of some mid-to-high-end motherboards. You only need to disconnect the power supply before using it.

How to reset bios on MSI x370?

There are many ways to reset the BIOS on MSI X370, including but not limited to the following three:

Enter the advanced interface of the BIOS (F7), and select in the settings→Save and Exit column Restore the default values ​​and confirm, then press F10 to save and exit. At this time, the BIOS will be restored to the default state.

Taking out the battery: Each motherboard has a CR2032 battery, which is used to save BIOS data when the power is off. Removing the battery for about 6 minutes during a power outage will cause the motherboard to completely lose BIOS information, and the settings in the BIOS will naturally return to their default state. However, it should be noted that as the number of components and interfaces on the motherboard increases, some CR2032 batteries on the motherboard may have a vertical design, and some may be hidden under the motherboard heat sink.

Back CLEAR CMOS switch: Some mid-to-high-end models come with a back CLEAR CMOS switch. Press and hold for a few seconds to restore BIOS settings when the device is powered off. This is very convenient for overclocking players who like to mess around.

It should be noted that before performing a BIOS reset, it is recommended to back up important BIOS settings to avoid irreversible consequences due to improper operation.

How to reset MSI’s new motherboard to BIOS factory settings?

Steps for MSI’s new motherboard settings to restore BIOS factory settings:

1. Press Del, F1 and other keys to enter the BIOS during power-on self-test, and select Load Fail-Safe Defaults, Load Optimized Defaults, etc. Menu with Defaluts (default). Note: Different motherboards have different shortcut key operations for entering the BIOS and menu items for loading default factory settings. Please refer to the motherboard user manual.

2. Shut down the computer, open the case, remove the CMOS button battery from the motherboard (usually there is only one), and put it back later. At this time, the BIOS has been restored to factory default values. This method is suitable for almost all desktop computer motherboards now and is simple to operate. If the first method cannot enter the BIOS and cannot find the menu for restoring factory default settings, the second method is recommended.

How to reset bios in MSI?

To reset MSI’s BIOS, you first need to enter the computer’s BIOS setup interface. When the computer starts, press the DEL or F2 key to enter the BIOS setup interface.

In the BIOS setup interface, find the "Load Default Settings" or "Restore Defaults" option, select it and press the confirmation key.

Then press the F10 key to save and exit the BIOS setup interface.

The computer will restart and restore the BIOS configuration to factory settings. Please note that be sure to back up important files and data before resetting the BIOS.

How to restore bois factory settings for MSI motherboard?

1. Restart our computer first. When the logo icon appears on boot, press the "F2" key to open the BIOS interface.

2. In the BIOS interface that opens, select and open the "Exit" option.

3. In the "Exit" window that opens, find and select "load setup defaults"

Select "yes" in the pop-up window to restore the motherboard's factory settings.

The above is the detailed content of How to restore MSI motherboard BIOS to default settings?. For more information, please follow other related articles on the PHP Chinese website!