What is the wiring method of B360 Xiaodiao motherboard?

How to wire the b360 Xiaodiao motherboard?

B360 Xiaodiao motherboard wiring steps are as follows: First connect the power cord and power cord plug in the chassis to the ATX power plug and CPU power plug on the motherboard, then connect the front panel wire control board cable, USB cable, Audio cables and hard drive light cables, etc.

Then insert the graphics card into the PCI-E slot, connect SATA devices such as hard disk and optical drive to the motherboard SATA interface, connect the memory, CPU fan, and finally connect the monitor, keyboard and mouse.

After the wiring is completed, start the computer. Pay attention to carefully read the motherboard manual when wiring to avoid connecting wrong lines.

How to connect the jumper on the computer motherboard?

Generally, the jumper connections on the corresponding chassis on the motherboard are as follows;

POWER SW=power on button, POWER LED=power on indicator light (with positive and negative polarity difference), RESET SW= Reset button, H.D.D LED=disk indicator light (with positive and negative polarity difference), HD AUDIO=high fidelity audio, USB (generally not specified, it refers to 2.0)

Normally, there are usually silk screen and The English corresponding to the chassis jumper can be connected directly; if there is no corresponding one, you can refer to the following:

How to connect the motherboard cable?

The connection method is as follows:

The first step is to screw the screw posts and plastic nails that come with the case or motherboard to fix the motherboard into the corresponding positions of the motherboard and the case.

The second step is to pry off the sealing piece of the I/O interface on the chassis. Tip: You can remove the baffle at the corresponding position on the back of the chassis according to the motherboard interface. These baffles are directly connected to the chassis and need to be pushed open with a screwdriver and then removed with needle-nose pliers. The additional baffles for the card positions can be determined as needed, rather than removing all the baffles.

The third step is to align the motherboard with the I/O interface and put it into the chassis.

Step 4: Finally, align the motherboard fixing holes with the screw posts and plastic nails, and then fix the motherboard with screws.

Step 5: Insert the power plug into the corresponding socket on the motherboard.

How to connect the motherboard startup cable?

The chassis startup pins on the motherboard are plugged into the first pair from the right in the upper row. There are four plugs on the motherboard chassis, which respectively control the boot, power indicator light, hard disk indicator light, and restart button. There are two rows of pins in the lower left corner of the motherboard. The upper row is four and the lower row is five. The first two rows from right to left are for power supply and the last two are indicator lights. The first two rows are from left to right. It's the hard drive, and the last two are reboots.

How to connect the motherboard circuit?

Connect the various lines on the motherboard to the corresponding hardware devices to make the computer work properly. The following are some common motherboard circuit connections:

1. Power circuit: Connect the 24-pin or 20-pin power connector on the motherboard to the power supply.

2. CPU power supply line: Connect the 4-pin or 8-pin CPU power supply interface on the motherboard to the power supply.

3. Memory power supply line: Connect the memory power supply interface on the motherboard to the power supply.

4. Graphics card power supply line: Connect the PCI-E power supply interface on the motherboard to the power supply.

5. Front panel wiring: Connect the power button, restart button, hard disk light, power light and other interfaces on the motherboard to the front panel.

6. USB line: Connect the USB interface on the motherboard to the front panel or rear panel of the chassis.

7. SATA line: Connect the SATA interface on the motherboard to the hard disk, optical drive and other devices.

8. Audio line: Connect the audio interface on the motherboard to speakers, headphones and other devices.

The above is the detailed content of What is the wiring method of B360 Xiaodiao motherboard?. For more information, please follow other related articles on the PHP Chinese website!