Why does the computer get stuck on the logo page?

It is a common problem that the computer is stuck on the logo page, and many people will encounter this situation. Usually, this situation can be caused by hardware or software issues. Hardware problems may include insufficient computer memory, a failed hard drive, or a motherboard problem. Software problems may be caused by operating system errors, driver conflicts, or virus infections. For this problem, PHP editor Youzi suggests trying some basic solutions, such as restarting the computer, checking the hardware connection, repairing the operating system, etc. If the problem persists, it is recommended to consult professional technical support or maintenance personnel for more accurate diagnosis and solutions.

What happens when the computer is stuck on the logo page?

Where the problem lies:

1. The hard disk probability is 70%. 2. The BIOS probability is 15%. 3. The memory probability is 10%. 4. Other reasons are 5%. Detection method: 1. The chassis is powered off and dismantled. Open the case and unplug the SATA cable (the cable connecting the hard drive to the motherboard), then power on and see if it is still stuck at the LOGO. If it's not stuck, it means there's a hard drive problem.

2. The above is invalid. The chassis is powered off, the motherboard battery is unplugged, and the COMS circuit is discharged (short-circuit the COMS pin). If you don’t know the pins, unplug the battery and short-circuit the positive and negative terminals in the battery holder on the motherboard (10 seconds). Power on without battery. See if the problem persists.

3. The above is invalid. If there are excess memory modules, replace the memory module for testing (insert it into a non-original slot). If there is no memory module, replace the memory module with a slot. If there are two or more memory sticks, try a single memory stick and insert it into a non-original slot.

4. If the above is invalid, consider that the BIOS program and other motherboard self-tests cannot pass. Go to the diagnostic card and check the running code. Solution: Hard drive problem>>>SATA cable troubleshooting>Excluding bad sectors and high latency>Partition troubleshooting (can be repartitioned)>Rebuild MBR. BIOS problems>>>Restore default values》Troubleshoot whether the BIOS program is damaged. Memory problem>>>Replace memory slot》If that doesn’t work, replace the memory. Other questions>>>It depends on the code running and the test results of multimeter and oscilloscope. The one-time coding may be incomplete, but the idea is generally clear. It would be a great pleasure if I could solve your problem. If the problem still cannot be solved, please report the details of the tests you have performed to me.

Asus motherboard is stuck on the logo interface?

After the ASUS motherboard is stuck on the logo interface after reinstalling the system, please refer to the following steps:

1. Turn on the computer and press F2 to enter the BIOS, select securebootmenu in the security tab, securebootcontrol press Enter and select Disable , press F10 to save;

2. After the computer restarts, click F2 to enter the BIOS, select LaunchCSM in the boot tab, press Enter to select Enable, and press F10 to save;

3. Restart After booting, press esc to select the startup item and select the corresponding startup method

The startup is stuck on the startup logo interface. How to solve it?

The computer always stays on the motherboard LOGO interface when it is turned on, indicating that problems are found during the power-on self-check process and need to be checked one by one to solve the problems before the system can be entered normally.

1. If the motherboard LOGO is displayed when the computer is turned on and the system cannot be entered, you need to restart and press the TAB key to skip the LOGO screen or continuously press the DEL key (F2 or other designated hotkeys for notebooks) when turning on the computer to enter the CMOS setting interface. Turn off Full Screen LOGO Show in the Advanced BIOS Features tab, see if the power-on self-test information can be displayed, and then determine the problem.

2. Under normal circumstances, you can press the F1 key to skip non-fatal errors and directly start the computer according to the black screen and white text prompts, or press the DEL key to enter CMOS, and then press F9 to load predefined parameters or select Load Optimized Defaults (load high-performance defaults) or Load Fail-Safe Defaults (load fail-safe defaults), and then press F10 to save, exit and restart.

3. If the originally set CMOS parameters are not saved after the power is turned off or the system time in the CMOS is restored to the factory time, it may be that the motherboard battery has failed. You need to replace the battery and then refer to step 2 to load the preset. Define parameters and save.

4. If the above operations are ineffective, it means there is a problem with the hardware. Generally, the memory is in poor contact due to oxidation, or the hard disk may be in poor connection due to poor connection or the hard disk master boot record is damaged. The memory needs to be re-plugged or unplugged. Hard disk, or repair the hard disk master boot record, or reinstall the system or replace the hard disk.

The computer keeps getting stuck on the motherboard logo interface. What’s going on?

The reason is a boot failure caused by poor contact of externally connected equipment. Whenever you encounter a problem where the computer is stuck on the LOGO screen when starting up, the first thing to check is the problem with the externally connected device. For example, keyboard, mouse, camera, USB wireless network card, mobile hard disk, U disk, etc., all external USB devices and PS/2 interface devices.

Boot failure caused by poor contact of the hard disk. Sometimes the hard drive data cable or poor contact of the hard drive can also cause the computer to be stuck on the LOGO screen when starting up. When this happens, a prerequisite is that during the device self-test, the hard disk detection program fails, or the hard disk cannot be detected.

Start-up failure caused by poor contact of the memory module. This situation is quite special and usually occurs on computers with multiple memory sticks. Computers with a single memory stick rarely suffer from this failure phenomenon. The main reason is that the memory module has poor contact or the memory module is incompatible, causing the computer to start up and get stuck on the LOGO screen.

The computer is stuck at the logo when it starts up?

Cause 1. Poor contact of external devices

Poor contact of external devices of the computer may also cause the computer to stop at the logo interface.

Solution: After booting normally, enter the BIOS setting page and check externally connected devices one by one, including keyboard, mouse, camera, USB wireless network card, mobile hard disk, U disk, etc. All external USB devices need to be removed, leaving only the monitor's video data cable. Confirm which device's interface has poor contact, and then replace it with a new one.

Cause 2. Computer system failure

The computer has some software installed that is incompatible with the system, which may cause the stuck logo to appear on boot. In addition, when browsing the web, malicious plug-ins are installed, or Trojan viruses cause the system to fail to boot normally, causing the computer to be stuck on the motherboard logo interface when booting.

Solution: Just reinstall the computer operating system.

Cause 3. Poor hard disk contact

Sometimes the hard disk data cable or the hard disk contact is poor, which can also cause the computer to start and get stuck on the motherboard logo interface.

Solution: Shut down the computer first, then remove the side cover of the computer case, try to unplug all the hard drive cables, and then restart the computer. If the logo screen no longer appears, it means that the problem is caused by the hard disk or the hard disk data cable, and a hard disk data cable needs to be replaced.

Cause 4. Memory module problem

Poor contact of the memory module, or the memory module is incompatible, can also cause the computer to start up and get stuck at the logo screen. This situation is quite special and is common when there are multiple memory sticks.

Solution: Open the side cover of the computer case, then insert and unplug all the memories, insert the individual memories one by one, and try to perform boot detection alternately. If there is a memory stick that fails the test, it may be that it is not clean. Wipe it clean and try again. If it still does not work after wiping it, it may be broken and need to be replaced with a new memory stick.

The computer is stuck on the motherboard logo when booting?

One of the reasons is boot failure caused by poor contact of externally connected equipment. Whenever you encounter a problem where the computer is stuck on the LOGO screen when starting up, the first thing to check is the problem with the externally connected device. For example, keyboard, mouse, camera, USB wireless network card, mobile hard disk, U disk, etc., all external USB devices and PS/2 interface devices.

The second reason is the boot failure caused by poor contact of the hard disk. Sometimes the hard drive data cable or poor contact of the hard drive can also cause the computer to be stuck on the LOGO screen when starting up. When this happens, a prerequisite is that during the device self-test, the hard disk detection program fails, or the hard disk cannot be detected.

The third problem is boot failure caused by poor contact of the memory module. This situation is quite special and usually occurs on computers with multiple memory sticks. Computers with a single memory stick rarely suffer from this failure phenomenon. The main reason is that the memory module has poor contact or the memory module is incompatible, causing the computer to start up and get stuck on the LOGO screen.

The solution is to dismantle the side cover of the computer case, then insert and unplug all the memories, insert the individual memories one by one, and try to perform boot detection alternately. If any memory stick fails the test, wipe the gold finger of the memory stick clean with rubber glue, or replace it with a brand new memory stick.

The computer is stuck on the motherboard LOGO interface when it is turned on? The

reason may be hardware failure or system problems. When the computer is turned on, the motherboard LOGO interface is usually displayed by the motherboard firmware (BIOS or UEFI). If the computer cannot enter the operating system, it may be caused by the following reasons: 1. Hardware failure: it may be the motherboard, memory module, hard disk Wait until there is a problem with the hardware. For example, damaged capacitors on the motherboard, poor memory module contact, hard drive failure, etc. may cause the computer to fail to start normally. 2. System problem: There may be an abnormality in the operating system, causing the computer to fail to start normally. For example, system file corruption, driver conflicts, etc. may cause the computer to get stuck on the motherboard LOGO interface. If you encounter this situation, you can try the following methods to troubleshoot and solve the problem: 1. Check the hardware connections: Make sure that the motherboard, memory module, hard disk and other hardware are well connected and not loose or damaged. 2. Clean the memory module: Remove the memory module, clean the gold finger part, and then reinsert it into the motherboard. 3. Reset BIOS settings: You can try to restore the BIOS settings to default values, which can be achieved by removing the motherboard battery or using the clear CMOS jumper on the motherboard. 4. Reinstall the operating system: If none of the above methods work, you can try reinstalling the operating system to ensure that the system files are complete. If none of the above methods can solve the problem, it is recommended to contact professional maintenance personnel or after-sales service for further troubleshooting and repair.

The above is the detailed content of Why does the computer get stuck on the logo page?. For more information, please follow other related articles on the PHP Chinese website!