The motherboard battery is a small battery on the computer motherboard. It is used to provide power to keep system time, date and other information continuously updated. However, over time, the motherboard battery will gradually fail and need to be replaced. So, how to replace the motherboard battery? Below, PHP editor Zimo will introduce you in detail the steps to replace the motherboard battery. First, turn off the computer and unplug it to ensure safe operation. Then, open the case and find the battery on the motherboard, which is generally round or square, usually the CR2032 model. Use a screwdriver or corresponding tool to gently loosen the buckle on the battery holder and take out the old battery. Next, insert the new battery into the battery holder correctly, paying attention to the polarity direction and ensuring that the positive and negative poles correspond. Finally, gently press the buckle of the battery holder to ensure that the new battery is securely installed. After completing the above steps, close the case again, plug in the power plug, and turn it on. With simple steps, you can successfully replace the motherboard battery and ensure the normal operation of the system.
The steps to replace the motherboard battery are as follows: 1. Replacing the motherboard battery requires following certain steps. 2. The motherboard battery is an important component used to save the computer's BIOS settings and system time. When the motherboard battery is low or damaged, it may cause the computer to fail to start normally or the time to be set incorrectly. 3. The specific steps to replace the motherboard battery are as follows: a. First, turn off the computer and disconnect the power cord to ensure safe operation. b. Open the computer main case and find the battery on the motherboard. The motherboard battery is usually a round coin-shaped battery, and the common model is CR2032. c. Using an appropriate tool, such as a screwdriver or your fingers, gently remove the battery from its socket. Be careful not to use excessive force to avoid damaging the socket or battery. d. Insert the new motherboard battery into the slot correctly, ensuring that the positive and negative poles are correctly aligned. Usually the positive side is up and the negative side is down. e. Reinstall the main chassis cover and reconnect the power cord. f. Turn on the computer, enter the BIOS setting interface, and check whether the system time and date are correct. If it is incorrect, manual adjustment is required. g. After completing the replacement of the motherboard battery, you can restart the computer and check whether it is working normally. Summary: When replacing the motherboard battery, you need to pay attention to safe operations and follow the correct steps to ensure the normal startup of the computer and the accuracy of time settings.
Step/Method 1
First shut down the computer and cut off all relevant power sources to the computer.
Step/Method 2
Open the case and look for the battery (be sure to use metal to eliminate static electricity when touching parts of the case to prevent injury).
Step/Method 3
The battery is not difficult to find. You will see a coin-sized thing on the motherboard, which is the battery.
Step/Method 4
First remove the battery. After observation, you can see that there will be a small clip next to the battery. Use a screwdriver to push it and the battery will pop out (if If there are no small clips, use a screwdriver and gently pry it open).
Step/Method 5
After taking it off, you can install the prepared new battery. Just put it in according to the position of the original battery, but be careful not to Even if the installation is backwards, don't make it very loose.
Steps to replace the computer motherboard battery:
The first step is, near the south bridge of the motherboard, there is a silver-white disc button battery with a plus sign on the back and about two centimeters in diameter.
The second step is to use a flat tool to press the latch on the CMOS battery holder.
The third step is to pop up the battery on the motherboard automatically and then take it out by hand.
Installing the battery: Place the side without the buckle first, then place the battery flat on the slot, press it with the side, and there will be a click. The battery replacement is completed.
1. First buy a new motherboard BIOS battery. Make sure it is the same number as the battery on your computer. It is usually 2032. Go to the computer store to buy one with the same model
2. Turn off the power of the computer, open the case cover, and you will see a round battery. The battery is very bright and easy to find. The diameter is about 1.5-2.0CM. Take out the battery. There are batteries for each motherboard. The seats are different, so the battery removal methods are also different. Generally, they are divided into three types: external button type, top pressure type, and top button type. Take out the battery carefully!
3. At this time, take out the battery you bought Take out the new battery, be careful not to mistake the positive and negative directions of the battery (there are signs on the battery), press it, it is installed, and then close the chassis cover.
1. First, open the computer case, and then find the motherboard battery on the computer's motherboard:
2. Then use a screwdriver to pry off the motherboard battery. Be careful not to use excessive force when it is tilted. , so as not to damage the motherboard:
3. Then you can remove the motherboard battery:
4. Before replacing the new battery, you can see the voltage and other models on the battery. Pay attention to Match the one on the old battery:
5. Finally, place the new battery into the battery slot, so that the desktop computer has successfully replaced the motherboard battery.
The above is the detailed content of How to replace the motherboard battery?. For more information, please follow other related articles on the PHP Chinese website!
![[Web front-end] Node.js quick start](https://img.php.cn/upload/course/000/000/067/662b5d34ba7c0227.png)
