ASUS Lingyao s4100 USB disk reinstallation system

php Xiaobian Yuzai will introduce to you the method of reinstalling the system of ASUS Lingyao s4100 USB disk. When using ASUS Lingyao s4100 USB disk to reinstall the system, we can complete it in simple steps. First, we need to prepare a usable USB flash drive and make sure its capacity is large enough. Next, we need to download the corresponding system image file and use tools to write it to the USB flash drive. Then, we need to set the USB flash drive as the boot device in the computer and restart the computer. Finally, we only need to follow the prompts to install the system. This method is simple and easy to implement and is suitable for most ASUS Lingyao s4100 USB disk reinstallation systems. I hope the above introduction can be helpful to you.

Therefore, my main task today is to show you the disassembly process of ASUS Lingyao S4100UQ. On the one hand, this allows friends who already own this notebook to know the correct steps to disassemble it to avoid damage when disassembling it by yourself. On the other hand, this can also show what optimizations ASUS product designers have made on the internal structure of this product.

The disassembly of ASUS Lingyao S4100UQ is very simple. Just use a Phillips screwdriver to unscrew the 11 screw holes on the bottom case, including the four screw holes on the side of the rotating shaft. , three in the middle and four screw holes on the bottom side. In addition, the screws inside the fuselage can also be unscrewed in the same way.

The screws on the bottom case of ASUS Lingyao S4100UQ are divided into two types: long and short. The long ones are distributed on the side of the shaft and in the middle, and there are four short screws on the bottom side. . During the disassembly process, be sure to place the unscrewed screws in categories, otherwise you will have trouble when reinstalling them.

In order to remove the keyboard cover of ASUS Lingyao S4100UQ, you can first unscrew the 11 screws on the bottom case. Then, you can use a plastic tab or a slightly harder plastic card to gently draw a circle at the seam between the bottom case and the keyboard surface. In this way, all the buckle structures will be unlocked, and then the keyboard cover can be easily removed.

This way of fixing the hardware on the bottom case can strengthen the overall internal structure. When removing the keyboard cover, you need to pay attention to the keyboard and touchpad cables connected to the motherboard. These cables can be removed in both directions. It is easier to unplug the motherboard side.

I think the hardware structure of ASUS Lingyao S4100UQ is designed very reasonably. The bottom side is the battery-based speaker and WiFi antenna module, and then the upper side is empty. A large 2.5-inch hard drive is installed on the motherboard and cooling module. Because of the existence of this 2.5-inch hard drive installation position, the I/O interface on the right side of the fuselage must be connected to the motherboard on the left side in the form of a cable.

Under the cable, there is a screw for fixing the battery.

#There is also a screw at a symmetrical position on the left side of the battery. After being unscrewed, the battery with a capacity of 42 watt hours can be removed.

To remove the motherboard part, first unscrew the three screws that fix the metal frame of the 2.5-inch hard drive, and then unscrew the cable connection on the right side of the fuselage that is only fixed by one screw. I/O interface module. Obviously there is only one screw removed from the I/O interface module, but why are there five screw holes on it? What if you don’t remember which screw hole to tighten when putting it back together? Don't worry, there are triangular graphic indicators next to each screw hole that needs to be tightened. Follow these instructions strictly and there will be no problems.

Unplug the monitor cable on the upper left, unscrew the two screws on the left side of the motherboard, and then unscrew the WiFi module on the lower left and the fixing screws of the fan on the upper right. The whole thing can be removed.

The front of the ASUS Lingyao S4100UQ motherboard is shown in the picture. It is natively equipped with an M.2 interface solid-state drive, and the memory part uses an onboard particle SO-DIMM DDR4 Expansion slot form.

The cooling module consists of heat pipes and fans, covering the CPU and graphics card.

The thermal base of the CPU part is fixed by four screws, and the GPU part is fixed by two diagonally distributed screws. Unplug the 4-Pin power supply jumper of the fan and unscrew the fixing screw to remove the entire cooling module.

#The structure used to fix the hinge of the screen body is very strong, and there are a total of four screws in the front and back.

The highly integrated internal hardware structure design of Lingyao S4100UQ allowed me to encounter no obstacles during the disassembly process. And when all the disassembled parts are laid out, the number can be counted on ten fingers. Okay, the disassembly work of ASUS Lingyao S4100UQ thin and light notebook is completed here, and then I will bring you the hardware upgrade guide of Lingyao S4100UQ. Editor of this article: Sun Duan Follow Paopao.com and enjoy technological life.

The above is the detailed content of ASUS Lingyao s4100 USB disk reinstallation system. For more information, please follow other related articles on the PHP Chinese website!