


Mingsu H61 motherboard can be equipped with a discrete graphics card! And how about the performance?
Mingsu H61. Motherboard, you can install a discrete graphics card! And how about the performance?
Depending on the purpose and budget, H61 is entry-level and low-end, and that’s it. Or you can replace the B75 motherboard and CPU with I5 3470, I7 3770, etc.
Can I buy the Mingsu b75 motherboard?
It is not recommended to buy. The B75 motherboard is an INTEL commercial 7 series commercial motherboard, which is equivalent to the low-end model of the Z77. It focuses on the mid-to-low-end market and was first used in the DIY market. It is famous for its cost-effectiveness. USB3.0, Both SATA3.0 and PCIE3.0 are available, and the maximum memory support is 1600, and it can support a maximum capacity of 32G, which is so much better than H61.
How many times do you press f to install the system using a USB flash drive on the Mingsu motherboard?
ESC, F12, DEL.
Insert the prepared boot USB disk into the desktop computer. When restarting the computer, keep pressing shortcut keys such as F12 or F11 or Esc or F7. The following are the USB boot hot disks for various brands of motherboards and desktop all-in-one computers. Key list.
According to different computer brands, select the corresponding button to bring up the startup menu selection interface.
If it is not supported, look at the following bios settings:
1. Old motherboard CMOS settings
1. Insert the U disk into the computer, restart and keep pressing Del or Press F2 or F1 or F10 or esc to enter the BIOS interface.
2. If it is the following interface, press the ↓ direction key to select Advanced BIOS Features and press Enter;
3. Press the ↓ direction Press the key to select Hard Disk Boot Priority and press Enter;
4. Select USB-HDD and press the plus or minus sign or F5/F6 or PageUP/PageDown to move to the first position. Press F10 and press Enter to restart to boot from the USB disk. .
How to plug in the Mingsu x58 motherboard?
The steps to install the Mingsu X58 motherboard socket are as follows: First, make sure the size of the motherboard matches the chassis. Then, place the motherboard on the bottom of the case and align it with the I/O board on the rear of the case. Next, align the motherboard's screw holes with the screw holes on the bottom of the case and use the screws to secure the motherboard to the case. Then, plug the power connector into the corresponding slot on the motherboard and make sure the connection is secure. Next, insert the memory slot into the corresponding slot on the motherboard and make sure it is inserted into place. Then, insert the processor into the CPU socket on the motherboard and press gently to ensure it is inserted into place. Finally, connect the hard drive, optical drive and other devices to the SATA slot on the motherboard, and connect the power cable and data cable. Once completed, close the case and connect the monitor, keyboard, and mouse. Now, you can start your computer and start using the Mingsu X58 motherboard.
How much does Intel x79plus motherboard cost?
Are you talking about the Mingsu X79-PLUS motherboard? This motherboard only costs 378 yuan. To be honest, the X79 platform is already very old. In addition, most of them are second-hand and no-name brands, so it is best Don’t buy the X79 platform. The latest Intel i3 8100 quad-core costs 569 yuan. The GALAXY H110-M.2 PLUS motherboard costs 399 yuan. The total cost is less than 1,000 yuan. Both the price and performance are very good.
Buy Is it better to buy a second-hand first-tier brand Gigabyte B75 motherboard with a three-month warranty on Taobao, or a brand-new second-tier brand Mingsu B75 motherboard with a two-year warranty on JD.com?
The so-called brand new B75 is refurbished. Secondly, this brand is not a second-tier brand. It is just a miscellaneous brand. The technical support is worse than you think! Furthermore, JD.com’s non-self-operated products are basically the same as those of TB, and there is no guarantee of after-sales service. So when I have no choice, I personally think it is better to buy a second-hand GA.
Does Mingsu b85m motherboard support m2 solid state?
Hello, yes, Mingsu B85M motherboard supports M.2 solid-state drives. It provides an M.2 slot that can be used to install an M.2 SSD. Please note that this motherboard only supports M.2 SATA SSD and does not support M.2 NVMe SSD.
Why can’t Mingsu motherboard G41 detect the network card?
Cannot detect the network card and cannot connect to the broadband are two different things.
The failure to detect the network card is a driver problem.
Just use Computer Manager to update the driver.
1. Open Tencent Computer Manager and click "Toolbox".
2. Find "Hardware Detection" in the toolbox.
3. Click "Driver Installation" in the hardware detection.
4. You can see the "Installation Status". If it is not installed, you can click to install it directly.
The above is the detailed content of Mingsu H61 motherboard can be equipped with a discrete graphics card! And how about the performance?. For more information, please follow other related articles on the PHP Chinese website!

Hot AI Tools

Undresser.AI Undress
AI-powered app for creating realistic nude photos

AI Clothes Remover
Online AI tool for removing clothes from photos.

Undress AI Tool
Undress images for free

Clothoff.io
AI clothes remover

Video Face Swap
Swap faces in any video effortlessly with our completely free AI face swap tool!

Hot Article

Hot Tools

Notepad++7.3.1
Easy-to-use and free code editor

SublimeText3 Chinese version
Chinese version, very easy to use

Zend Studio 13.0.1
Powerful PHP integrated development environment

Dreamweaver CS6
Visual web development tools

SublimeText3 Mac version
God-level code editing software (SublimeText3)

Hot Topics



Can I access the Internet by plugging the network cable directly into my computer? If it is a desktop, it cannot be used directly. You need to open the computer network sharing center, find the adapter interface, and click on the Ethernet card properties. Then open settings, click the "Configuration" option, select "Advanced" and find the connection speed and duplex mode. Finally, change "Automatic Detection" to "10M Duplex" or "10M Half-Duplex", and click to confirm that there is a router. Connect the computer to the router with a network cable to access the Internet. Use a network cable to connect the LAN interface of the computer and the router. After the connection is completed, you can access the Internet normally. Can you access the Internet after checking that the host is online? Under normal circumstances, the new computer will be able to access the Internet as long as all the hardware drivers are installed, including the network card driver. ,So

How to set up the U disk boot in the HP notebook bios (how to enter the HP computer bios) and then insert the U disk to be booted first into the USB port of the notebook. If you want to install the system, the system program must have been prepared in the U disk. First, open the laptop. Make sure the laptop is turned off. Setting the bios must be done with the computer turned off. Then insert the U disk that you want to boot first into the USB port of the notebook. If you want to install the system, the prerequisite is that the system program has been prepared in the U disk. Take the HP ProDesk400G5SFF desktop computer as an example. Set the BIOS disk startup method: First, restart the computer and wait for the startup screen to appear. There are two ways to set up USB disk startup on HP notebooks. One is to directly press the shortcut key to select

Tutorial on assembling a computer and installing a system? Nowadays, the system installation for assembling computers is very simple and convenient, and only requires a CD. First enter the bios settings, set the computer to boot first with the CD-ROM drive, then restart the computer and load the system CD into the CD-ROM drive. The CD will automatically enter the installation state. At this time, you only need to manually repartition the partitions, and the rest will be completed automatically. How to install win11 system when assembling a computer? 1. First, we need to download a win11 image file from this site before installing it. 2. The win11 image file has undergone a large number of professional tests to ensure stable installation and smooth operation. 3. After the download is completed, load the folder in the download path and run the "windowssetup" process in it.

How to connect a Huawei phone to a computer via USB to access the Internet. First, we open the phone settings and search for "HDB". Then we click to open "Mobile Network Sharing" in More. Then we can click to open "USB Sharing Network" in the pop-up window. Summary First, connect the Huawei mobile phone to the computer through the data cable. Open "Settings" on your phone and enter the settings interface. Click "Personal Hotspot", select "USB tethering" and click the switch button at the back to turn it on. First click "Settings About Phone", then click "Version Number" 7 times in succession. You will be prompted to enter developer mode. Then return to the "Settings" list, "Developer Options" will appear, then click to enter "Developer Options", turn on the "USB Debugging" switch, and click

How to enter bios after assembling a computer? Before entering the BIOS, you need to make sure that the computer is completely shut down and powered off. Here are several common ways to enter the BIOS: 1. Use shortcut keys: Most computer manufacturers will display a prompt message at startup telling you which key to press to enter the BIOS settings. Usually the F2, F10, F12 or Delete key. After pressing the appropriate keys, you should be able to see a screen with information about your computer's hardware and BIOS settings. 2. Use the button on the motherboard: Some computer motherboards have a dedicated button for entering BIOS settings. This button is usually labeled "BIOS" or "UEFI". After pressing the button you should be able to see

How to cancel the MSI motherboard icon when booting 1. Press the DEL key when booting to enter the BIOS. Generally, in the "Advanced Features" item, you can find the words MSI motherboard LOGO screen. Select DISABLED, save and exit. There will no longer be this MSI motherboard LOGO screen when you turn on the computer in the future. MSI motherboard refers to the motherboard brand developed by MSI (MSI Technology Company). 2. The logo displayed when the computer is turned on is basically that of the motherboard manufacturer. You can set QUICKPOST to DISENABLE in the BIOS, so that the logo will generally no longer be displayed. It will display computer configuration-related information and give you more details. 3. First, teach you how to flash the BIOS in Windows environment. First: Go online

1. Win11 does not have very high requirements for the motherboard. You can first download healthcheck or whynotwin11 to check whether your other hardware devices support it (you can download it from this site). 2. If other conditions are met and only tpm does not meet the requirements, you can enable tpm in the bios settings. 3. Restart the system, and then press [DEL] on the keyboard to enter the BIOS settings when the logo pops up. 4. Enter the [Settings] option and [Miscellaneous] option in sequence. 5. Find [Intel Platform Trust Technology (PTT)] below and set it to [Start]. 6. If it is an AMD platform, then

1. Gigabyte motherboard 1. First, we restart the computer and use the keyboard [DEL] to enter the BIOS settings when restarting. 2. Find and enter the [Settings] tab above. 3. Then find and enter [Miscellaneous] under settings. 4. Set [Intel Platform Trust Technology (PTT)] to [Enabled]. 5. After the settings are completed, use the keyboard [F10] to save, and then click [YES] to exit. 2. ASUS motherboard 1. First restart the computer and continuously tap [del] on the keyboard to enter the bios settings when booting. 2. Click [AdvancedMode] or press [F7] to find [A
