php editor Xiaoxin today introduces to you how to install the small pinholes on the motherboard. During the process of assembling a computer, there are often some small pinholes on the motherboard. These small pinholes are actually used to install other hardware devices. Let's take a closer look at how to correctly install the small pinholes on the motherboard. First, we need to confirm the purpose and location of the small pinhole, and then select the appropriate pin for installation. When inserting the pin into the small pinhole, pay attention to the direction and angle of insertion to ensure that the pin is aligned with the small pinhole. Finally, gently press down on the pins to make sure they are securely connected to the motherboard. In this way, we have successfully installed the small pinhole on the motherboard and can continue with subsequent hardware device installation. I hope this simple guide helps you all!
The small pinholes on the motherboard are stuck on the motherboard slot with terminals. You can install them directly.
Motherboard front panel pins
1. You can open the case and find the case The wire that connects the power button.
There are two pins on the corresponding motherboard. Shorting those two pins will turn on the computer.
Pressing the button is actually a short circuit, and the motherboard receives the signal to turn on.
(The power supply of the chassis is actually always on, it is not a true power-off shutdown)
2. The power supply is plugged into the interface of the motherboard, the one with more than ten wires in a bundle Interface, short any two black and orange wires to turn it on.
3. The power switch of the chassis is connected to the motherboard of the computer through a wire. If you unplug this wire from the motherboard, you will find two pins. Use the key to shorten the two pins. That's it.
4. Pull out the motherboard electromagnet and put it back after 30 seconds. Or replace the jumper on the side of the solenoid.
Lenovo computer battery replacement
Step one: Turn off the power of the computer and remove all data cables and related equipment plugged into the chassis.
Step 2: Place the back of the computer up on the table, and use a screwdriver to unscrew the screws on the back cover. Be careful to touch metal with your hands before touching computer hardware to prevent static electricity from damaging the hardware.
Step 3: After opening the back cover, the hardware facilities of the laptop can be seen at a glance. We can see the analytics battery on the motherboard, which is similar to the size of a coin.
Step 4: Use a small screwdriver to hold the small clip next to the motherboard battery and loosen the battery screw. Then one end of the battery will lift up and take it out. But some batteries are stuck directly inside and can be pried out directly with a screwdriver. Finally, the battery from the Apple laptop was successfully removed.
Motherboard batteries are universal, and the common voltage is 1.5V. In order to protect the motherboard from operating normally, it is necessary to power the crystal oscillator on the motherboard for a long time, so a battery is installed on the motherboard and used to provide accurate time information to the motherboard. The motherboard battery has a very long service life, some of which can exceed ten years. Most batteries on motherboards are the same model, but there are exceptions.
To install the six-hole power supply on the motherboard, you need to follow the following steps:
First, make sure that the motherboard and the power supply are turned off.
Then, insert one end of the six-hole power supply plug into the six-hole power supply interface on the motherboard.
Next, plug the other end into the six-hole power socket of the power supply. Make sure the plug is perfectly aligned with the socket and push in gently until the plug is fully inserted into the socket.
Finally, check that the connection is secure, then turn on the power and test whether the motherboard is working properly. Please note that care must be taken during installation to avoid bending or damaging the plug.
Usually about 2-3 years. Subject to the specific circumstances of use. When the battery is insufficient, the time will return to the factory date, and the hardware information used during startup will be recorded, that is, the BIOS information that maintains CMOS.
Replace the battery and turn off the computer's power. Open the case cover and you will see a round battery. The diameter is about 1.5-2.0CM, take out the battery, and then take out the new battery and install it. Pay attention to the direction of the positive and negative poles of the mercury battery. Then replace the battery according to the reverse action of removing the battery just now, and it is installed. Then close the case lid. Then restart the computer and make various CMOS settings.
Need not. When assembling a desktop computer, the power supply and the motherboard are structurally completely independent and are only connected through a pluggable power cord. When disassembling the power supply, you only need to pull out the power cords connected to the motherboard without disassembling the motherboard. Operation steps:
1. Wear an electrostatic ring or touch grounded metal to prevent and discharge static electricity from the human body.
Second, open the outer cover of the chassis.
Third, take photos inside the case or mark all power plugs (for novices, not necessary for experienced ones.).
Fourth, pull out all power plugs inside.
5. Unscrew the power supply fixing screw and take out the power supply. Just reverse the installation process.
Calculator can still be used normally without battery. Calculator usually has dual power supply design, one is battery and the other is solar panel. Since the calculator display is an e-ink screen and consumes a lot of power, a small solar panel is enough for the calculator to work properly.
If the calculator is not equipped with a battery, it needs to be placed in a relatively bright place. As long as there is light, it cannot generate power. It does not have to be placed under the sun. Leaving the drawer in a dark environment for a long time may cause the calculator to run out of power and fail to turn on.
The answer is as follows: Mitsubishi CNC battery replacement steps are as follows:
1. Turn off the power of the CNC machine tool and unplug the power plug to ensure safety.
2. Open the electrical cabinet door of the CNC machine tool, find the battery, and unplug the battery cable.
3. Use a screwdriver to unscrew the battery fixing screw and take out the battery.
4. Install the new battery into the battery holder and secure the screws.
5. Insert the battery cable into the positive and negative terminals of the new battery.
6. Close the electrical cabinet door, plug in the power plug, and turn on the power of the CNC machine tool.
7. Check whether the battery is working properly, and deal with any abnormalities in time.
Notes:
1. When replacing the battery, you should pay attention to the safety of the power source and ensure that the power is turned off before proceeding.
2. When replacing the battery, use the same specification and model as the original battery.
3. When replacing the battery, pay attention to the positive and negative connections of the battery to avoid reverse connection.
4. After replacing the battery, a battery test should be performed to ensure that the battery is working properly.
The above is the detailed content of How to install the small pinhole on the motherboard?. For more information, please follow other related articles on the PHP Chinese website!
![[Web front-end] Node.js quick start](https://img.php.cn/upload/course/000/000/067/662b5d34ba7c0227.png)
