If it is a satellite axis, it is very simple. Pull off the keycaps in the row above the space bar first, and then pull them out directly with your hands. But the force should be even and don't break the space bar.
Before disassembling the space bar, you must first remove the lower cover. The lower cover is the bottom of the keyboard and contains all the switches. Since mechanical keyboard lower covers are usually held in place by screws, a screwdriver is required to remove them. First, you need to determine which screws need to be removed.
First remove the screws at the back. For a mechanical keyboard, we first remove the screws on the back of the keyboard one by one. On some keyboards, after you feel the steel wire inside the key, you can remove the space bar by pushing the space bar to the left or right.
Mechanical keyboard keycaps need to be removed. There are two common types of key pullers for mechanical keyboards: "steel wire key pullers" and "standard key pullers". Currently, the former is more commonly used, while the latter is cheaper, usually only a few yuan each online.
If it is a mechanical keyboard, you can disassemble it like this: first remove the two ALTs next to the space bar, then lift it up with both hands. There is a steel wire inside, and then push the space bar to the right or left. , can be removed. Clean the keyboard after taking it off. You can use a hair dryer to blow away the dust, or wipe it clean with a paper towel.
Shutdown When disassembling any parts of the laptop, we must first shut down the computer to avoid unnecessary damage to the computer. This is a very important step and cannot be omitted.
First prepare the DELL laptop. Before disassembling, turn the computer over and remove the bottom shell. You can see that there is a very important screw in the center. Its function is to fix the keyboard and optical drive. . So, be sure to unscrew it before prying the keyboard open.
First remove the relatively long shift key. First, hold the upper edge with your hands and pull it upward. The keyboard cap will come off, as shown in the picture below. You can see that the keycap and base are connected by a steel wire, as shown in the picture below.
To make sure there is no damage, the X-shaped bracket is connected under the keycap. First, remove the X-shaped bracket under the keycap. Use your index finger to press one side of the bracket in the picture below, and slowly apply force. The other side of the bracket will be pushed out from the groove marked with a red circle. The other bracket is simple, just pull it up and it comes out.
Step one: Prepare the tools (fine cross screwdriver, slotted screwdriver, tweezers, blade, soft cloth) and the notebook to be disassembled . Step 2: Remove the battery. Turn the back of the notebook upward, open the battery lock, and take out the battery.
The method is very simple. Just pull it diagonally in your direction with a little force. However, there may be two results. One is to pull out the button bracket together, and the other is to just pull out the button. cap.
The technique for disassembling the E450 keyboard is: push the keyboard toward the screen, lift the keyboard up slightly after snapping it out, and pull it out (don’t use too much force, there is a cable at the front connected to the motherboard to avoid hardware damage. Damage. Figure 4 After taking out the keyboard, turn it over directly. You can see the circled area in Figure 5.
The Lenovo notebook may have a black screen when it is turned on. The following problems may occur: Monitor connection problem, check if the monitor is Correct connection and whether the switch is turned on. For computer problems, observe whether the computer has a startup sound and whether it starts normally. Check whether there is a problem with the memory. You can try to replace the memory bar or check if it is loose.
Open it first Thinkpad e450c laptop, click the "Settings" icon. Then in the interface, click the "Devices" option. Then in the interface, click the "Mouse and Touchpad" option. Then in the interface, click "Other Mouse Options" Option.
1. The method of disassembly and installation of notebook keyboard keys is as follows: Disassembly: The ease of removing the keys is actually about the same as doing "1 1" .Pick the top of the button with your hand, use a little force to pull it in your direction, and the button will be removed.
2. First prepare the DELL notebook. Before disassembling, turn the computer over and remove it. On the bottom shell, you can see that there is a very important screw in the center. It is used to fix the keyboard and optical drive. Therefore, be sure to unscrew it before prying off the keyboard.
3. Disassembly: Use a knife or other pointed object to gently lift one end of the key. You will see two cross supports (X-shaped) inside. Use a slender tool to insert into the cross supports (the four above X area), move the end point of the tool to the Let’s take a look at the structure of the keys. The first button to be removed is
5. Detailed instructions for installation and disassembly of laptop keyboard keys are as follows: 0. First tilt the laptop keyboard downward about 45°. 0Then insert a fingernail into the button to be removed. 0 Then use your fingernails to push downwards around the button to remove the button. 0Removed button.
6. Use your finger clip to reach into the lower left corner of the space bar, then apply a little force upward, and the left latch will open. As shown in the picture below, this is the effect after turning on both sides of the space bar. Hold both sides of the space bar with both hands and push it in the direction marked by the arrow in the picture below to remove it. The picture below shows the disassembled space bar.
The above is the detailed content of Removal and installation of laptop keyboard keys. For more information, please follow other related articles on the PHP Chinese website!
![[Web front-end] Node.js quick start](https://img.php.cn/upload/course/000/000/067/662b5d34ba7c0227.png)
