1. Restart the computer and enter safe mode. If you are able to successfully enter Safe Mode without a blue screen issue, there may be a driver or application issue. You can try to uninstall recently installed software or drivers, or restore the system to a previous point in time. Check if the hardware device is working properly.
2. When a blue screen appears on your computer, you may need to restart your computer to solve the problem. Here are some basic steps: First, press the power button on the computer host and hold it for a few seconds until the computer turns off. Wait a few seconds, then press the power button again to start the computer.
3. The most common blue screen is the memory problem: use an eraser to clean the golden fingers of the memory stick, clean the dust on the chassis, and clean the memory slots.
4. You can cut off the power first, open the computer case, take out the memory stick, and use an eraser to rub the golden finger area (that is, the place with the copper piece) back and forth a few times. Then change another memory slot and plug it back in, and that's it. Press F8 while booting up, enter Advanced, select Last Known Good Configuration, and OK.
If this happens, you can try to use the system recovery function. Press F8 when booting and select the "System Repair" option. If this method does not solve the problem, you can consider reinstalling the system. Virus removal Viruses may also be one of the causes of a blue screen on your computer.
The first method is to enter the BIOS interface of the computer, find the "Intogratedperipherals" option, and then just change the value of the "SATAConfiguration" item to IDE to complete the solution. Second, try to start Windows in safe mode. Press the F8 key when booting and select "Safe Mode".
Reinstall the operating system: If the above method cannot solve the problem, you can reinstall the operating system. First, you need to prepare a system recovery disk or a USB boot disk with system installation function. After entering the BIOS settings, set the boot disk as the preferred boot device, and then follow the prompts to install the system.
You can try the following solutions: First, try restarting your computer. Sometimes, the blue screen problem may be caused by a temporary problem with the system, and restarting may solve the problem. If restarting doesn't work, you can try starting your computer in safe mode.
When the computer starts with a blue screen, press the "F8" key repeatedly. Right-click on the Start menu bar. Select the Control Panel option. Click "Uninstall a program" under the last option "Programs". Find "KB2859537" and uninstall it. Restart the computer to return to normal, as shown in the figure.
The solution is to turn on the computer and press the DEL key (or the key prompted on the boot screen) to enter the motherboard BIOS and initialize the BIOS setting information. Usually press F9 to restore the factory default settings, then press F10 to save and exit and restart the computer. 3. CMOS (BIOS) setting error, mainly due to problems with software setting options.
If you still see the blue screen error after performing the operation, please try to roll back, disable or uninstall the recently installed driver. Roll back, disable, or uninstall drivers: If you have recently installed new drivers, you can roll back, disable, or uninstall them to determine if this is the cause of the problem.
Method Perform startup repair Startup repair can solve some common startup problems in Windows systems. You can use this feature in Windows RE. In Windows RE, click "Troubleshoot" and then click "Advanced Options". Select Startup Repair and wait for completion.
Methods to deal with frequent blue screen problems on computers: Click to open 360 Security Guard, open its interface and find "Manual Service" at the bottom, enter "blue screen" in the input box and search. After searching for the solution, you can see the relevant solution below the input box, and click "Repair Now" behind it.
First check whether the computer has started to start the operating system when it is turned on. If it freezes, blue screen or automatically restarts when starting the operating system, it means that the partition table and master boot record of the hard disk are normal, and the cause of the problem is that the hard disk partition table is damaged, the hard disk master boot record is damaged, and the hard disk partition end mark is lost.
It is difficult to prevent. Some viruses and Trojans infect system files, causing system file errors or exhaustion of system resources. They may also cause a blue screen. Solution: It is recommended to install anti-virus software with strong anti-virus capabilities and perform anti-virus regularly.
You can cut off the power first, open the computer case, take out the memory stick, use an eraser to rub the gold finger part (that is, the place with the copper piece) back and forth a few times, and then replace it. Just plug one memory slot back in and that's it. Press F8 while booting up, enter Advanced, select Last Known Good Configuration, and OK.
The computer starts up with a blue screen, indicating that your computer needs to be repaired and the required devices are not connected or cannot be accessed. Error code: 0xc000000f Unable to enter the system. You can press the Enter key to try again, but it does not work. You can also press F8 to enter safe mode, but it doesn't work either. Pressing F9 to use other operating systems does not work.
Restart the system. When the startup menu appears, press the F8 key. The windows advanced startup options menu will appear. Keyboard cursor, select: Last Known Good Configuration, then press Enter (Enter), Enter ( Enter), press it.
The blue screen is caused by computer operation: due to abnormal shutdown or forced shutdown, the blue screen is caused, or some irregular operation is performed before the blue screen, causing the blue screen. You can press F8 to enter the safe mode, delete, uninstall, and cancel your previous operations.
First press and hold the power switch for 10 seconds to force shutdown. After confirming the shutdown, click the power button again to turn it on, and continuously click the F8 key on the keyboard until the advanced options menu appears (as shown below). Use the direction key "↓" in the lower right corner of the keyboard to select "Safe Mode" and press "Enter", then select the current system and press "Enter".
1. The computer is accidentally installed with malware, or malicious programs are generated while surfing the Internet. It is recommended to use 360 Guard, Software such as Kingsoft Defender can clean up junk and kill malware. Once completed, restart the computer and the problem may be solved. If it doesn't work, reinstalling and restoring the system can solve the problems caused by the software.
2. Restart the computer: Sometimes the blue screen problem may be caused by a temporary error, and a simple restart may solve the problem. Check for hardware issues: A blue screen can sometimes be related to hardware failure. You can check whether the hardware connections are loose, such as memory modules, hard drives, etc., and make sure they are all firmly connected.
3. Restart the computer. If you can enter the system normally, it means that the last abnormality was just an occasional program or system operation error and does not matter.
4. There are several reasons for computer blue screen: memory problem (removing it and applying it sometimes can solve the problem, but generally memory problems are caused by the memory being broken), system problem (reinstalling will do the trick), hard disk problem ( The hard disk has bad sectors. You can use DOS commands to repair it, or use the efficiency source to repair it.
5. A blue screen appears when the computer is turned on, indicating that your computer needs to be repaired and the required equipment is not connected or cannot be accessed. Error code: 0xc000000f If you can't enter the system, you can press Enter to try again, but it doesn't work. You can also press F8 to enter safe mode, but it doesn't work. Press F9 to use other operating systems, but it doesn't work.
The above is the detailed content of Computer starts up and displays blue screen recovery. For more information, please follow other related articles on the PHP Chinese website!
![[Web front-end] Node.js quick start](https://img.php.cn/upload/course/000/000/067/662b5d34ba7c0227.png)
