, large independent graphics card, anti-detachment is normal, find a suitable wooden stick, support it between the end of the graphics card and the chassis , or use cotton thread to tie the gap between the graphics card and the chassis. The thread should have pull-down force to hold the graphics card down.
, to prevent the hook from being detached and broken, you can find a good tail hook from a scrap motherboard and repair it, or tie it with cotton thread and wrap the graphics card and the motherboard interface tightly.
Restart, delete the graphics card driver in the normal mode of the Windows system, and restart the computer. You don't have to go into safe mode. In a pure DOS environment, edit the system. INI file, change display.drv=pnpdrver to display.drv=vga.drv, save and exit, and then update the driver in Windows.
Solution: If you are very hands-on, you can use a fine needle to pull out the hundreds of shrapnel one by one. Don't pull too much, otherwise it will break if the top end of the shrapnel is pulled out! This is treating a dead horse as a living horse. If you don't want to go through this trouble, just replace it with a motherboard with the same specifications.
Poor contact with graphics card. Take the rubber tea and rub it a few times. The graphics card cannot dissipate heat. An additional heat sink or fan is required. The room has air conditioning to cool it down.
Pull out the graphics card, gently wipe the gold finger with an eraser, and then try to insert it again. The graphics card slot has a lock card, which must lock the graphics card and place the graphics card on the rear bezel. Fasten the screws.
. For a large independent graphics card, the anti-detachment function is normal. Find a suitable wooden stick and hold it between the end of the graphics card and the case, or use cotton thread. When bundling the graphics card and the chassis, the wire must have pull-down force to hold the graphics card down.
What should I do if my computer graphics card is loose? The screen looks like this. Your picture looks like a driver problem. Please update the graphics card driver first. You can use Driver Wizard to update. Answers to computer questions.
Find a suitable wooden stick and place it between the end of the graphics card and the chassis, or use cotton thread to tie the gap between the graphics card and the chassis. The thread should have pull-down force to hold the graphics card down. 2. If the anti-hook is broken, you can find a good tail hook from the old motherboard and repair it, or tie it with cotton thread to wrap the graphics card and the motherboard interface tightly.
Pull out the graphics card, gently wipe the gold finger with an eraser, and then try to insert it again. The graphics card slot has a lock card, which must lock the graphics card and place the graphics card on the rear bezel. Fasten the screws.
The graphics card has poor contact. Take the rubber tea and rub it a few times. The graphics card cannot dissipate heat. An additional heat sink or fan is required. The room has air conditioning to cool it down.
First loosen the motherboard screws, plug in the graphics card, adjust the graphics card to a comfortable position, then tighten the motherboard mounting screws, and finally tighten the graphics card screws. In addition, tighten the fixing screws of the graphics card bezel.
Is it damaged? If it is damaged, don’t ask someone to repair it. Replace the graphics card. If it is not damaged, wipe it clean with alcohol and try again. Before wiping, touch the faucet to remove static electricity. Check the motherboard slot to see if there is any foreign matter inside. It is best to use an electrostatic brush (available in the market).
one. The memory is loose. As a result, the self-test cannot pass. You can solve this kind of fault by plugging and unplugging it again. two. The graphics card is loose. As a result, the self-test cannot be correctly identified. You can also solve this kind of fault by plugging and unplugging it again. three. The data cable between the monitor and graphics card is not connected properly.
Keeps ringing: The power supply, monitor and graphics card are not connected properly. Repeated short beeps: There is a problem with the power supply. AMI BIOS: 1 short: Memory refresh failed. The solution is to replace the memory module. 2 short: Memory ECC verification error. Solution: Enter CMOS settings and turn off ECC verification.
1. For a large independent graphics card, if the anti-detachment function is normal, find a suitable wooden stick and hold it between the end of the graphics card and the chassis, or use Bundle the cotton thread between the graphics card and the chassis. The thread should have pull-down force to hold the graphics card down.
2. You can pull out the graphics card and wipe the gold finger, preferably with an eraser, to clean the graphics card slot, then plug in the graphics card and secure it. At the same time, wipe the memory stick in the same way. This phenomenon should not occur (hardware damage).
3. To prevent the hook from being detached and broken, you can find a good tail hook from the scrap motherboard and repair it, or tie it with cotton thread to wrap the graphics card and the motherboard interface tightly.
4. Unplug the graphics card, gently wipe the gold finger with an eraser, and then try to insert it again. The graphics card slot has a lock card, which must lock the graphics card and place the graphics card on the back bezel. The upper screws are fixed.
5. Your problem is with the graphics card slot on the motherboard. In several slots on the motherboard, aluminum springs are used to contact the gold fingers on the board.
6. Type 1: A blue screen suddenly occurs when playing games. Normally, the graphics card is soldered. The second type: After frequent use, the screen suddenly becomes blurry or the screen is abnormal. Normally, the graphics card is faulty. The third type: garbled characters that fill the screen suddenly appear while using it. Normally, the graphics card is damaged.
A loose graphics card will cause: The graphics card temperature is too high: The graphics card GPU or video memory temperature is too high, resulting in blurry screen. Generally, the overheating of the graphics card may be caused by the interference of foreign matter such as dust in the fan, which slows down or stops the fan speed. The graphics card is incompatible with the motherboard, causing screen distortion.
The first type: A blue screen suddenly occurs when playing games. Normally, it is caused by a weak soldering of the graphics card. The second type: After frequent use, the screen suddenly becomes blurry or the screen is abnormal. Normally, the graphics card is faulty. The third type: garbled characters that fill the screen suddenly appear while using it. Normally, the graphics card is damaged.
Question 6: The independent computer graphics card is always loose. How to solve the problem of loose graphics card? It is common that large graphics cards are too heavy, causing the interface to deform, or the tail hook of the motherboard PCI-E interface is anti-detachment and breaks, and the graphics card cannot be locked and fixed. , leading to looseness.
1. For a large independent graphics card, the anti-detachment function is normal. Find a suitable wooden stick and hold it between the end of the graphics card and the chassis. , or use cotton thread to tie the gap between the graphics card and the chassis. The thread should have pull-down force to hold the graphics card down.
2. If it is an independent graphics card, plug the data cable into the integrated graphics card. If the problem is eliminated, it proves that the problem is with the independent graphics card. Take out the independent graphics card, clean the gold finger of the independent graphics card and then reinstall it. Plug it in. If that doesn't solve the problem, it means the discrete graphics card is broken.
3. You can pull out the graphics card and you can see that the AGP slot is completely consistent with the graphics card interface. The pins of the graphics card may become rusty or dusty after being used for a long time. Just wipe the pins with an eraser to keep them clean.
4. Solution: If you are very hands-on, you can use a fine needle to pull out the hundreds of shrapnel one by one. Don't pull too much, otherwise it will break if the top end of the shrapnel is pulled out! This is treating a dead horse as a living horse. If you don't want to go through this trouble, just replace it with a motherboard with the same specifications.
The above is the detailed content of What should I do if my laptop graphics card is loose?. For more information, please follow other related articles on the PHP Chinese website!
![[Web front-end] Node.js quick start](https://img.php.cn/upload/course/000/000/067/662b5d34ba7c0227.png)
