How to wire the assembled computer?

When assembling a computer, wiring is a crucial step. Incorrect wiring can cause the computer to fail to start or run unstable. How to properly connect the various components of your computer? In order to answer this question, PHP editor Strawberry will provide you with detailed guidance, from connecting the motherboard to the installation of the graphics card and hard disk, explaining step by step the specific steps and precautions for wiring. Readers who want to learn more about the techniques for assembling computer wiring, please continue reading below.

How to wire the assembled computer

During the DIY installation process, many friends have asked how to wire the assembled computer. I have introduced many computer assembly tutorials before. Most of the connection methods involved in power cords are mentioned in one stroke. In view of the fact that novice friends currently have some problems with the installation details, the editor will introduce in detail how to wire the assembled computer.

Assembling computer wiring

The front panel connections of the chassis generally include front audio, front USB, 1394. power indicator light, hard disk indicator light, power on, restart, these connections, Look carefully at the picture, it is: power indicator light, hard disk indicator light, power on, restart wiring diagram, the motherboard manual usually has instructions, if not, look at the motherboard and it is also written, pay attention to the position of the pins, 9.10 is not The connection is basically like this. The HD-LED on the motherboard is the hard disk working indicator light, so plug the wire with: H..D.D.LED on it. The SP-LED on the motherboard is the power supply working indicator light, just Plug in the positive and negative ends of the wires that have P LED written on them. If the positive and negative ends of these two indicator lights are plugged in reversely, the lights will not light up after power is turned on. For the one that does not light up, just change the positive and negative directions.

The RST on the motherboard is the reset button. Plug in the one with RESET SW written on the wire. The PW-BN on the motherboard is the power-on button. Plug in the one with POWER SW written on the wire.

SPEAKER is The front buzzer is divided into " " and " - " phases; it can happen no matter how you connect an ordinary speaker, but it is special here. Since the voltage value of 5V is provided on the " " phase, we must install it correctly to ensure that the buzzer sounds.

The following is the front audio. The F-AUDIO on the motherboard is the location of the front audio interface. It is different from the USB. The USB has one less pin on the side, and the front audio is on the 4th pin. Pin, just plug it into the corresponding position

The front panel connection is completed. Finally, connect the power supply and hard disk. The SATA data cable is in the shape of an inverted 7-character row. Don’t worry about plugging it in wrongly. , the wrong one cannot be inserted. The hard disk movie cable is wider than the data cable and has the same shape. Connect it to the hard disk

just align it and insert it. Plug the other end of the SATA data cable into On the motherboard's SATA interface. That's it. Next, connect the power supply to the motherboard. The

motherboard supplies 24P power. The old motherboard used to be 20P, so I took it out and used the 8P power supply for the 4 active

CPUs on the side. There are also 4P ones, just take off 4 of them. The motherboard and CPU power supplies are designed to be fool-proof. Don’t worry about plugging them in wrongly. You won’t be able to plug them in if they are in the wrong direction.

Connect to the corresponding interface, look at the motherboard interface diagram above, the graphics card power supply is 6P, there are also 8P, it can be disassembled, just plug in the graphics card power interface and it is done,

install it Done. If your case is side-transparent, you can install a strip of rotating light, which will look much better. If it is not side-transparent, there is no need to install it. You can use the back-line case and put the cables at the back. This way it looks beautiful and is easy to install. After finishing, untie the threads and tie up the ones that need to be tied up with zip ties so that they look comfortable.

The above is the detailed content of How to wire the assembled computer?. For more information, please follow other related articles on the PHP Chinese website!