Motherboard chassis wiring

How to plug in the switch cable of the computer host

The method of connecting the switch cable of the computer host is as follows: First, connect the power cord from the chassis. There is a comparison The wide one, if it's marked USB, is the cable connecting the USB socket on the chassis panel. Look for the USB pin on the edge of the motherboard and plug it in.

Find the plug with the POWER (PWR) mark on the chassis panel, then find the corresponding marked pin on the motherboard and insert it. Often the chassis wiring will be marked with their respective identities or English abbreviations, just like the model number of the monitor. Players can easily distinguish them through such logos.

First connect the power cord from the chassis, one of which is wider, as shown by the arrow in the picture below. If it's labeled USB, it's the cable that connects to the USB slot on the case panel. Find the USB pin on the edge of the motherboard and plug it in.

How to connect the jumpers on the chassis motherboard

How to connect the jumpers on the computer motherboard: Arrange all the wires together, and first clarify the definition of each wire according to the above markings : a. Power switch: POWER SW, possible names: POWER, POWER SWITCH, ONOFF, POWER SETUP, PWR, etc. Function definition: reset button on the front of the chassis.

What types of motherboard jumpers are there? When connecting the power switch cable to the power switch cable, first find the two-pin plug marked "powersw" on the chassis panel cable, which is white and brown, and then Just plug it into the pin marked "pwrsw" or "PWR" on the motherboard.

When we install the motherboard into the chassis, the main connected jumpers are: power switch (Power Switch), restart switch (Restart Switch), power indicator light (POWER LED), hard disk indicator light (HDD LED), front USB0, front USB0, front audio hole (AUDIO).

How to connect the front USB plug of the chassis to the computer motherboard

1. First, arrange the USB cable of the chassis smoothly. The neutral line includes the USB interface of the chassis and the button line of the switch. On the motherboard, you can find the interface for connecting USB, and the letters USB will appear next to the interface. Plug the USB cable of the chassis into the USB port of the motherboard and the connection is successful.

2. You only need to install the CPU, memory, motherboard, graphics card and hard disk into the chassis in order. Although the USB interface on the front of the chassis is quite simple to connect, you must be careful.

3. First find the front USB cable of the chassis. Then plug in the connecting cable according to the pins marked on the front USB of the motherboard.

4. The first step is to smooth out the USB cables in the chassis, which include the switch button cable and the USB interface cable of the chassis. Find an interface marked with USB letters next to it on the motherboard. That is the interface used to connect USB. Insert the USB cable of the chassis into the USB port of the motherboard. After the connection is successful.

5. This set of pins should be from Biostar's motherboard. In fact, the pins are already printed on the motherboard. The top 2 pins on the right are boot pins, the 3 pins on the left are power indicator lights (divided into - three pins); the bottom 2 pins on the right are restart pins, and the 2 pins on the left are hard disk indicator lights (divided into - two pins), specifically Refer to the picture below to connect.

How to wire the computer host

1. Step 1: First put the computer and the host in the same place, then plug the power cord on the host into the power port of the host, and plug the other end of the power cord into Power outlet. Step 2: Find the VGA interface on the host, connect one end of the VGA cable to the VGA interface on the host, and connect the other end of the VGA cable to the computer monitor.

2. First, connect the power cord from the chassis. One of them is relatively wide, as pointed by the arrow in the picture below. If it is marked USB, then it is connected to the USB on the chassis panel. For the socket cable, look for the USB pin on the edge of the motherboard and plug it in. This one is relatively large and easy to find.

3. First connect the power cord from the chassis, one of which is wider, as shown by the arrow in the picture below. If it's labeled USB, it's the cable that connects to the USB slot on the case panel. Find the USB pin on the edge of the motherboard and plug it in.

4. The flat plug is a data cable used to connect the monitor and the host, called a high-definition data cable. Just plug in the power cord of the host. Computer wiring instructions reset switch two-pin.

The above is the detailed content of Motherboard chassis wiring. For more information, please follow other related articles on the PHP Chinese website!