linux如何安装php

本文我们主要和大家分享linux如何安装php，本文以图文的形式和大家分享，希望能帮助到大家。

1.从php官网下载相应的版本

因为php下载页面只有最近的几个版本，下载比较老的版本在下载页面已经找不到了，只能手动通过下面的url来下载，

http://cn.php.net/distributions/php-5.3.9.tar.bz2，此页面里会列出一些老的版本，此处使用的是5.3版本，下载的是gz格式的

2.安装php

将tar包解压，进入解压包目录-执行命令：./configure --prefix=/opt/local/php ，“/opt/local/php”是安装路径，可以改成自己希望的安装路径。

（1）此处可能会提示缺少一些必须的插件，此时利用yum命令进行安装，比如最可能报的错误：configure error xml2-config not found. please check your libxml2 installation，此时执行命令：yum -y install libxml2 libxml2-devel，安装相应插件，以此类推

所有插件安装完成后，再次执行

<span style="font-size: 14px;">./configure --prefix=/opt/local/php<br/></span>

（2）此处如果是要安装php-fpm的功能的话需要yum安装更多插件，例如：

<span style="font-size: 14px;">yum -y install openssl openssl-devel bzip2 bzip2-devel curl curl-devel readline-devel fcgi php-mcrypt libmcrypt libmcrypt-devel<br/></span>

其中安装php-mcrypt libmcrypt libmcrypt-devel时可能会提示找不到包，这时要通过更新源解决，具体命令如下：

<span style="font-size: 14px;">yum -y install epel-release<br/>yum update<br/></span>

其中，update执行了两次才成功，之后再执行configure

./configure --prefix=/opt/local/php5.3.29 --with-config-file-path=/etc --enable-inline-optimization --disable-debug --disable-rpath --enable-shared --enable-opcache --enable-fpm --with-fpm-user=www --with-fpm-group=www --with-mysql=mysqlnd --with-mysqli=mysqlnd --with-pdo-mysql=mysqlnd --with-gettext --enable-mbstring --with-iconv --with-mcrypt --with-mhash --with-openssl --enable-bcmath --enable-soap --with-libxml-dir --enable-pcntl --enable-shmop --enable-sysvmsg --enable-sysvsem --enable-sysvshm --enable-sockets --with-curl --with-zlib --enable-zip --with-bz2 --with-readline --without-sqlite3 --without-pdo-sqlite --with-pear

通过后执行make

此时可能会出现以下提示

PEAR package PHP_Archive not installed: generated phar will require PHP's phar extension be enabled.

此处可暂进忽略，等之后再行安装，再次在php目录执行make all install

如果安装了php-fpm，则还需要执行以下命令，将php/etc目录下的配置文件拷贝一份

cp etc/php-fpm.conf.default etc/php-fpm.conf

将php/lib/php.ini拷贝到/etc/下

3.初装phar

这时可以执行

<span style="font-size: 14px;">wget http://pear.php.net/go-pear.phar<br/></span>

之后再执行

/opt/local/php/bin/php /opt/local/go-pear.phar

在出现的提示后，选1，选择phar安装目录，然后一路回车进行安装即可

最后制作php软链，让php全局可用

<span style="font-size: 14px;">ln -s /opt/local/php/bin/php /usr/bin/php<br/></span>

4.验证

执行php -v和sbin/php-fpm -v查看php版本以验证php是否已安装

5.启动php-fpm

php/sbin/php-fpm

INT, TERM 立刻终止

QUIT 平滑终止

USR1 重新打开日志文件

USR2 平滑重载所有worker进程并重新载入配置和二进制模块

示例：

php-fpm 关闭：

kill -INT `cat /opt/local/php/var/run/php-fpm.pid`

php-fpm 重启：

kill -USR2 `cat /opt/local/php/var/run/php-fpm.pid`

如果找不到php-fpm.pid文件，可通过查找php-fpm进程号进行重启和关闭

例如

<span style="font-size: 14px;">[root@SH-DEV local]# ps -aux|grep php-fpm<br/>root     141735  0.0  0.0 201840  3892 ?       <br/> Ss   16:27   0:00 php-fpm: master process (/opt/local/php5.3.29/etc/php-fpm.conf)<br/><br/>kill -USR2 141735<br/></span>

6.修改php-fpm配置

（1）如果在nginx.conf中使用了fastcgi_pass unix:/tmp/php-cgi.sock，则需要修改php-fpm.conf，找到如下码段：

<span style="font-size: 14px;">; The address on which to accept FastCGI requests.<br/>; Valid syntaxes are:<br/>;   &#39;ip.add.re.ss:port&#39;    - to listen on a TCP socket to a specific address on<br/>;                            a specific port;<br/>;   &#39;port&#39;                 - to listen on a TCP socket to all addresses on a<br/>;                            specific port;<br/>;   &#39;/path/to/unix/socket&#39; - to listen on a unix socket.<br/>; Note: This value is mandatory.<br/>;listen = 127.0.0.1:9000<br/>listen = /tmp/php-cgi.sock<br/><br/>; Set listen(2) backlog. A value of &#39;-1&#39; means unlimited.<br/>; Default Value: 128 (-1 on FreeBSD and OpenBSD)<br/>;listen.backlog = -1<br/><br/>; Set permissions for unix socket, if one is used. In Linux, read/write<br/>; permissions must be set in order to allow connections from a web server. Many<br/>; BSD-derived systems allow connections regardless of permissions.<br/>; Default Values: user and group are set as the running user<br/>;                 mode is set to 0660<br/>listen.owner = nobody<br/>listen.group = nobody<br/>listen.mode = 0660<br/></span>

将原listen和listen.owner，listen.group段做如上修改，其中listen.owner，listen.group为nginx启动用户名，如此处不修改，会提示

nginx error connect to php-fpm.sock failed (13: Permission denied)

当然此处如果将sock放在内存中/dev/shm/php-fpm.sock会更快

（2）修改php-fpm线程数

<span style="font-size: 14px;">; Per pool prefix<br/>; It only applies on the following directives:<br/>; - &#39;slowlog&#39;<br/>; - &#39;listen&#39; (unixsocket)<br/>; - &#39;chroot&#39;<br/>; - &#39;chdir&#39;<br/>; - &#39;php_values&#39;<br/>; - &#39;php_admin_values&#39;<br/>;   dynamic - the number of child processes are set dynamically based on the<br/>;             following directives. With this process management, there will be<br/>;             always at least 1 children.<br/>;             pm.max_children      - the maximum number of children that can<br/>;                                    be alive at the same time.<br/>;             pm.start_servers     - the number of children created on startup.<br/>;             pm.min_spare_servers - the minimum number of children in &#39;idle&#39;<br/>;                                    state (waiting to process). If the number<br/>;                                    of &#39;idle&#39; processes is less than this<br/>;                                    number then some children will be created.<br/>;             pm.max_spare_servers - the maximum number of children in &#39;idle&#39;<br/>;                                    state (waiting to process). If the number<br/>;                                    of &#39;idle&#39; processes is greater than this<br/>;                                    number then some children will be killed.<br/>;  ondemand - no children are created at startup. Children will be forked when<br/>;             new requests will connect. The following parameter are used:<br/>;             pm.max_children           - the maximum number of children that<br/>;                                         can be alive at the same time.<br/>;             pm.process_idle_timeout   - The number of seconds after which<br/>;                                         an idle process will be killed.<br/>; Note: This value is mandatory.<br/>pm = dynamic<br/>#如何控制子进程，选项有static和dynamic。如果选择static，则由pm.max_children指定固定的子进程数。如果选择dynamic，则由下面的参数决定<br/><br/>; The number of child processes to be created when pm is set to &#39;static&#39; and the<br/>; maximum number of child processes when pm is set to &#39;dynamic&#39; or &#39;ondemand&#39;.<br/>; This value sets the limit on the number of simultaneous requests that will be<br/>; served. Equivalent to the ApacheMaxClients directive with mpm_prefork.<br/>; Equivalent to the PHP_FCGI_CHILDREN environment variable in the original PHP<br/>; CGI. The below defaults are based on a server without much resources. Don&#39;t<br/>; forget to tweak pm.* to fit your needs.<br/>; Note: Used when pm is set to &#39;static&#39;, &#39;dynamic&#39; or &#39;ondemand&#39;<br/>; Note: This value is mandatory.<br/>pm.max_children = 8<br/>#子进程最大数<br/><br/>; The number of child processes created on startup.<br/>; Note: Used only when pm is set to &#39;dynamic&#39;<br/>; Default Value: min_spare_servers + (max_spare_servers - min_spare_servers) / 2<br/>pm.start_servers = 8<br/>#启动时的进程数<br/><br/><br/>; The desired minimum number of idle server processes.<br/>; Note: Used only when pm is set to &#39;dynamic&#39;<br/>; Note: Mandatory when pm is set to &#39;dynamic&#39;<br/>pm.min_spare_servers = 1<br/>#保证空闲进程数最小值，如果空闲进程小于此值，则创建新的子进程<br/><br/>; The desired maximum number of idle server processes.<br/>; Note: Used only when pm is set to &#39;dynamic&#39;<br/>; Note: Mandatory when pm is set to &#39;dynamic&#39;<br/>pm.max_spare_servers = 8<br/>#保证空闲进程数最大值，如果空闲进程大于此值，此进行清理<br/></span>

相关推荐：

Linux上安装php-mysqlnd扩展实例

mac安装php开发环境方法实例分享

最详细的linux安装php过程

Atas ialah kandungan terperinci linux如何安装php. Untuk maklumat lanjut, sila ikut artikel berkaitan lain di laman web China PHP!