安装LNMP环境，PHP5.4.37版本安装成功，添加php-fpm服务到系统启动项时，报错service php-fpm does not support chkconfig；php-fpm服务不支持chkconfig；
编辑/etc/init.d/php-fpm启动脚本，打开之后是乱码，查找原因是拷贝php-fpm启动脚本文件错误。
从同样环境下同样的php版本拷贝php-fpm启动脚本，重新编辑黏贴过来，保存退出后，可以正常加入启动项；有遇到同样情况的朋友可以直接复制脚本，保持与脚本内容的路径一样即可。
php-fpm启动脚本参考如下：
#! /bin/sh### BEGIN INIT INFO# Provides: php-fpm# Required-Start: $remote_fs $network# Required-Stop: $remote_fs $network# Default-Start: 2 3 4 5# Default-Stop: 0 1 6# Short-Description: starts php-fpm# Description: starts the PHP FastCGI Process Manager daemon### END INIT INFOprefix=/usr/local/phpexec_prefix=${prefix}php_fpm_BIN=${exec_prefix}/sbin/php-fpmphp_fpm_CONF=${prefix}/etc/php-fpm.confphp_fpm_PID=${prefix}/var/run/php-fpm.pidphp_opts="--fpm-config $php_fpm_CONF --pid $php_fpm_PID"wait_for_pid () { try=0 while test $try -lt 35 ; do case "$1" in 'created') if [ -f "$2" ] ; then try='' break fi ;; 'removed') if [ ! -f "$2" ] ; then try='' break fi ;; esac echo -n . try=`expr $try + 1` sleep 1 done}case "$1" in start) echo -n "Starting php-fpm " $php_fpm_BIN --daemonize $php_opts if [ "$?" != 0 ] ; then echo " failed" exit 1 fi wait_for_pid created $php_fpm_PID if [ -n "$try" ] ; then echo " failed" exit 1 else echo " done" fi ;; stop) echo -n "Gracefully shutting down php-fpm " if [ ! -r $php_fpm_PID ] ; then echo "warning, no pid file found - php-fpm is not running ?" exit 1 fi kill -QUIT `cat $php_fpm_PID` wait_for_pid removed $php_fpm_PID if [ -n "$try" ] ; then echo " failed. Use force-quit" exit 1 else echo " done" fi ;; status) if [ ! -r $php_fpm_PID ] ; then echo "php-fpm is stopped" exit 0 fi PID=`cat $php_fpm_PID` if ps -p $PID | grep -q $PID; then echo "php-fpm (pid $PID) is running..." else echo "php-fpm dead but pid file exists" fi ;; force-quit) echo -n "Terminating php-fpm " if [ ! -r $php_fpm_PID ] ; then echo "warning, no pid file found - php-fpm is not running ?" exit 1 fi kill -TERM `cat $php_fpm_PID` wait_for_pid removed $php_fpm_PID if [ -n "$try" ] ; then echo " failed" exit 1 else echo " done" fi ;; restart) $0 stop $0 start ;; reload) echo -n "Reload service php-fpm " if [ ! -r $php_fpm_PID ] ; then echo "warning, no pid file found - php-fpm is not running ?" exit 1 fi kill -USR2 `cat $php_fpm_PID` echo " done" ;; *) echo "Usage: $0 {start|stop|force-quit|restart|reload|status}" exit 1 ;;esac
